Effect of surface topography and residual stress on the taper connection stability in total hip arthroplasty

Fretting-corrosion in hip taper modular junctions: The influence of topography and pH levels – An in-vitro study

(2021) Dmitry Royhman et al.   Journal of the Mechanical Behavior of Biomedical Materials

Microstructural aspects of Ti6Al4V degradation in H2O2-containing phosphate buffered saline

(2021) M. Prestat et al.   CORROSION SCIENCE

Atomic Scale Origin of Metal Ion Release from Hip Implant Taper Junctions

(2020) Shanoob Balachandran et al.   Advanced Science

Corrosion Behavior of Surface-Treated Metallic Implant Materials

(2020) Therese Bormann et al.   Materials

A review on the finite element simulation of fretting wear and corrosion in the taper junction of hip replacement implants

(2020) Mohsen Feyzi et al.   COMPUTERS IN BIOLOGY AND MEDICINE

Microstructure, mechanical and corrosion properties of magnesium alloy bone plate treated by high-energy shot peening

(2019) Shu-xu WU et al.   TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA

Effect of simulated inflammatory conditions and potential on dissolution and surface oxide of CoCrMo alloy: In situ electrochemical atomic force microscopy study

(2018) Yangping Liu et al.   ELECTROCHIMICA ACTA

Improvement of corrosion resistance of AA2024-T3 using femtosecond laser peening without protective and confining medium

(2018) Uroš Trdan et al.   CORROSION SCIENCE

Head Taper Corrosion Causing Head Bottoming Out and Consecutive Gross Stem Taper Failure in Total Hip Arthroplasty

(2018) Michael M. Morlock et al.   JOURNAL OF ARTHROPLASTY

Same Same but Different? 12/14 Stem and Head Tapers in Total Hip Arthroplasty

(2017) Ulrike Mueller et al.   JOURNAL OF ARTHROPLASTY

Do Stem Taper Microgrooves Influence Taper Corrosion in Total Hip Arthroplasty? A Matched Cohort Retrieval Study

(2017) Christina M. Arnholt et al.   JOURNAL OF ARTHROPLASTY

Mechanical, chemical and biological damage modes within head-neck tapers of CoCrMo and Ti6Al4V contemporary hip replacements

(2017) Deborah J. Hall et al.   JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART B-APPLIED BIOMATERIALS

Effect of trunnion roughness and length on the modular taper junction strength under typical intraoperative assembly forces

(2017) S.Y. Jauch-Matt et al.   MEDICAL ENGINEERING & PHYSICS

The effect of simulated inflammatory conditions and pH on fretting corrosion of CoCrMo alloy surfaces

(2017) Yangping Liu et al.   WEAR

Does Surface Topography Play a Role in Taper Damage in Head-neck Modular Junctions?

(2016) Robin Pourzal et al.   CLINICAL ORTHOPAEDICS AND RELATED RESEARCH

Shorter, rough trunnion surfaces are associated with higher taper wear rates than longer, smooth trunnion surfaces in a contemporary large head metal-on-metal total hip arthroplasty system

(2015) Timothy M. Brock et al.   JOURNAL OF ORTHOPAEDIC RESEARCH

Quantification of the Contact Area at the Head-Stem Taper Interface of Modular Hip Prostheses

(2015) Florian Witt et al.   PLoS One

Fatigue Performance of Medical Ti6Al4V Alloy after Mechanical Surface Treatments

(2015) Robert Sonntag et al.   PLoS One

Directin vivoinflammatory cell-induced corrosion of CoCrMo alloy orthopedic implant surfaces

(2014) Jeremy L. Gilbert et al.   JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART A

Variations in the trunnion surface topography between different commercially available hip replacement stems

(2014) Selin Munir et al.   JOURNAL OF ORTHOPAEDIC RESEARCH

The Influence of Head Size on Corrosion and Fretting Behaviour at the Head-Neck Interface of Artificial Hip Joints

(2013) Richard M.R. Dyrkacz et al.   JOURNAL OF ARTHROPLASTY

Enhanced wear and corrosion in modular tapers in total hip replacement is associated with the contact area and surface topography

(2013) Anna Panagiotidou et al.   JOURNAL OF ORTHOPAEDIC RESEARCH

Material loss at the taper junction of retrieved large head metal-on-metal total hip replacements

(2013) Ashley K. Matthies et al.   JOURNAL OF ORTHOPAEDIC RESEARCH

Effect of residual stress induced by pulsed-laser irradiation on initiation of chloride stress corrosion cracking in stainless steel

(2013) Shuzo Eto et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Why does titanium alloy wear cobalt chrome alloy despite lower bulk hardness: A nanoindentation study?

(2013) N. Moharrami et al.   THIN SOLID FILMS

Prediction of machining induced residual stresses in turning of titanium and nickel based alloys with experiments and finite element simulations

(2012) T. Özel et al.   CIRP ANNALS-MANUFACTURING TECHNOLOGY

Influence of assembly procedure and material combination on the strength of the taper connection at the head–neck junction of modular hip endoprostheses

(2011) Annelie Rehmer et al.   CLINICAL BIOMECHANICS

Surface integrity in high speed end milling of titanium alloy Ti–6Al–4V

(2010) A. Daymi et al.   MATERIALS SCIENCE AND TECHNOLOGY

Impact magnitudes applied by surgeons and their importance when applying the femoral head onto the Morse taper for total hip arthroplasty

(2008) Jake P. Heiney et al.   ARCHIVES OF ORTHOPAEDIC AND TRAUMA SURGERY