Achieving high damping and excellent ductility of Al Mg alloy sheet by the coupling effect of Mg content and fine grain structure

Effects of high Mg content and processing parameters on Portevin-Le Chatelier and negative strain rate sensitivity effects in Al–Mg alloys

(2020) Chang-Hee Cho et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

High strength and large ductility of a fine-grained Al–Mg alloy processed by high strain rate hot rolling and cold rolling

(2020) Xinyu Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Dynamic recrystallization behaviors of high Mg alloyed Al-Mg alloy during high strain rate rolling deformation

(2019) Xinyu Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effects of large amounts of Mg (5–13 wt%) on hot compressive deformation behavior and processing maps of Al-Mg alloys

(2019) H.T. Jeong et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Effects of low temperature aging precipitates on damping and mechanical properties of ZK60 magnesium alloy

(2019) Xiongpeng Zhou et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Effects of solid solution elements on damping capacities of binary magnesium alloys

(2019) Lang Yu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Evaluation of microstructure, damping capacity and mechanical properties of Al-35Zn and Al-35Zn-0.5Sc alloys

(2018) H.J. Jiang et al.   JOURNAL OF ALLOYS AND COMPOUNDS

High damping capacity of Al alloys produced by friction stir processing

(2018) C.Y. Liu et al.   MATERIALS CHARACTERIZATION

Significant strengthening in superlight Al-Mg alloy with an exceptionally large amount of Mg (13 wt%) after cold rolling

(2018) D.H. Jang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effects of the stacking fault energy fluctuations on the strengthening of alloys

(2018) Yifei Zeng et al.   ACTA MATERIALIA

Fabrication of Al–35Zn alloys with excellent damping capacity and mechanical properties

(2017) H.J. Jiang et al.   JOURNAL OF ALLOYS AND COMPOUNDS

High strength and ductile high solid solution Al–Mg alloy processed by a novel hard-plate rolling route

(2017) Min Zha et al.   JOURNAL OF ALLOYS AND COMPOUNDS

An improved thermo-mechanical treatment of high-strength Al–Zn–Mg–Cu alloy for effective grain refinement and ductility modification

(2017) W.T. Huo et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Mechanical properties, intergranular corrosion behavior and microstructure of Zn modified Al–Mg alloys

(2014) Chunyan Meng et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Achieve high ductility and strength in an Al–Mg alloy by severe plastic deformation combined with inter-pass annealing

(2014) Min Zha et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy

(2013) Kaka Ma et al.   ACTA MATERIALIA

A study of the ultrahigh damping capacities in Mg–Mn alloys

(2012) Jingfeng Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

High tensile ductility via enhanced strain hardening in ultrafine-grained Cu

(2011) P. Xue et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

A Study on the Combined Treatment of Cryorolling, Short-Annealing, and Aging for the Development of Ultrafine-Grained Al 6063 Alloy with Enhanced Strength and Ductility

(2010) Sushanta Kumar Panigrahi et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Effect of Mg content on the minimum grain size of Al–Mg alloys obtained by friction stir processing

(2010) Taiki Morishige et al.   SCRIPTA MATERIALIA

Strengthening mechanisms in an Al–Mg alloy

(2009) E.L. Huskins et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure behavior of Al–Mg–Sc alloy processed by ECAP at elevated temperature

(2008) O. Sitdikov et al.   ACTA MATERIALIA

Tougher ultrafine grain Cu via high-angle grain boundaries and low dislocation density

(2008) Y. H. Zhao et al.   APPLIED PHYSICS LETTERS

Prediction of Dislocation Cores in Aluminum from Density Functional Theory

(2008) C. Woodward et al.   PHYSICAL REVIEW LETTERS

Application of damping mechanism model and stacking fault probability in Fe–Mn alloy

(2007) S.K. Huang et al.   MATERIALS CHARACTERIZATION

Effect of Si and Cr on stacking fault probability and damping capacity of Fe–Mn alloy

(2007) S.K. Huang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING