Achieving high damping and excellent ductility of Al Mg alloy sheet by the coupling effect of Mg content and fine grain structure
出版年份 2021 全文链接
标题
Achieving high damping and excellent ductility of Al Mg alloy sheet by the coupling effect of Mg content and fine grain structure
作者
关键词
Fine grains, Al-Mg alloy sheets, High damping capacity, High ductility, Extended dislocations
出版物
MATERIALS CHARACTERIZATION
Volume 174, Issue -, Pages 110974
出版商
Elsevier BV
发表日期
2021-02-18
DOI
10.1016/j.matchar.2021.110974
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Effects of high Mg content and processing parameters on Portevin-Le Chatelier and negative strain rate sensitivity effects in Al–Mg alloys
- (2020) Chang-Hee Cho et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- High strength and large ductility of a fine-grained Al–Mg alloy processed by high strain rate hot rolling and cold rolling
- (2020) Xinyu Li et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Dynamic recrystallization behaviors of high Mg alloyed Al-Mg alloy during high strain rate rolling deformation
- (2019) Xinyu Li et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Effects of large amounts of Mg (5–13 wt%) on hot compressive deformation behavior and processing maps of Al-Mg alloys
- (2019) H.T. Jeong et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Effects of low temperature aging precipitates on damping and mechanical properties of ZK60 magnesium alloy
- (2019) Xiongpeng Zhou et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Effects of solid solution elements on damping capacities of binary magnesium alloys
- (2019) Lang Yu et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Evaluation of microstructure, damping capacity and mechanical properties of Al-35Zn and Al-35Zn-0.5Sc alloys
- (2018) H.J. Jiang et al. JOURNAL OF ALLOYS AND COMPOUNDS
- High damping capacity of Al alloys produced by friction stir processing
- (2018) C.Y. Liu et al. MATERIALS CHARACTERIZATION
- Significant strengthening in superlight Al-Mg alloy with an exceptionally large amount of Mg (13 wt%) after cold rolling
- (2018) D.H. Jang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Effects of the stacking fault energy fluctuations on the strengthening of alloys
- (2018) Yifei Zeng et al. ACTA MATERIALIA
- Fabrication of Al–35Zn alloys with excellent damping capacity and mechanical properties
- (2017) H.J. Jiang et al. JOURNAL OF ALLOYS AND COMPOUNDS
- High strength and ductile high solid solution Al–Mg alloy processed by a novel hard-plate rolling route
- (2017) Min Zha et al. JOURNAL OF ALLOYS AND COMPOUNDS
- An improved thermo-mechanical treatment of high-strength Al–Zn–Mg–Cu alloy for effective grain refinement and ductility modification
- (2017) W.T. Huo et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Mechanical properties, intergranular corrosion behavior and microstructure of Zn modified Al–Mg alloys
- (2014) Chunyan Meng et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Achieve high ductility and strength in an Al–Mg alloy by severe plastic deformation combined with inter-pass annealing
- (2014) Min Zha et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy
- (2013) Kaka Ma et al. ACTA MATERIALIA
- A study of the ultrahigh damping capacities in Mg–Mn alloys
- (2012) Jingfeng Wang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- High tensile ductility via enhanced strain hardening in ultrafine-grained Cu
- (2011) P. Xue et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- A Study on the Combined Treatment of Cryorolling, Short-Annealing, and Aging for the Development of Ultrafine-Grained Al 6063 Alloy with Enhanced Strength and Ductility
- (2010) Sushanta Kumar Panigrahi et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Effect of Mg content on the minimum grain size of Al–Mg alloys obtained by friction stir processing
- (2010) Taiki Morishige et al. SCRIPTA MATERIALIA
- Strengthening mechanisms in an Al–Mg alloy
- (2009) E.L. Huskins et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Microstructure behavior of Al–Mg–Sc alloy processed by ECAP at elevated temperature
- (2008) O. Sitdikov et al. ACTA MATERIALIA
- Tougher ultrafine grain Cu via high-angle grain boundaries and low dislocation density
- (2008) Y. H. Zhao et al. APPLIED PHYSICS LETTERS
- Prediction of Dislocation Cores in Aluminum from Density Functional Theory
- (2008) C. Woodward et al. PHYSICAL REVIEW LETTERS
- Application of damping mechanism model and stacking fault probability in Fe–Mn alloy
- (2007) S.K. Huang et al. MATERIALS CHARACTERIZATION
- Effect of Si and Cr on stacking fault probability and damping capacity of Fe–Mn alloy
- (2007) S.K. Huang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
Publish scientific posters with Peeref
Peeref publishes scientific posters from all research disciplines. Our Diamond Open Access policy means free access to content and no publication fees for authors.
Learn MoreCreate your own webinar
Interested in hosting your own webinar? Check the schedule and propose your idea to the Peeref Content Team.
Create Now