An Experimental Investigation on the Progressive Failure of an Additively Manufactured Laser Powder Bed Fusion Ti-6Al-4V Aero-engine Bracket under Low Cycle Fatigue

Hot dwell-fatigue behaviour of additively manufactured AlSi10Mg alloy: Relaxation, cyclic softening and fracture mechanisms

(2021) Jianguang Bao et al.   INTERNATIONAL JOURNAL OF FATIGUE

Establishing specimen property to part performance relationships for laser beam powder bed fusion additive manufacturing

(2021) Arash Soltani-Tehrani et al.   INTERNATIONAL JOURNAL OF FATIGUE

Simulation of fatigue small crack growth in additive manufactured Ti–6Al–4V material

(2020) A. Gupta et al.   CONTINUUM MECHANICS AND THERMODYNAMICS

Analysis of the effect of internal defects on fatigue performance of additive manufactured metals

(2020) Niloofar Sanaei et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

A new approach to correlate the defect population with the fatigue life of selective laser melted Ti-6Al-4V alloy

(2020) Y.N. Hu et al.   INTERNATIONAL JOURNAL OF FATIGUE

The effect of manufacturing defects on the fatigue life of selective laser melted Ti-6Al-4V structures

(2020) Y.N. Hu et al.   MATERIALS & DESIGN

Methods and materials for additive manufacturing: A critical review on advancements and challenges

(2020) M Bhuvanesh Kumar et al.   THIN-WALLED STRUCTURES

Cyclic plastic behavior of additively manufactured Ti-6Al-4V under uniaxial and multiaxial non-proportional loading

(2019) Stefano Bressan et al.   INTERNATIONAL JOURNAL OF FATIGUE

Effect of strain amplitude on low cycle fatigue and microstructure evolution in Ti-6Al-4V: A TKD and TEM characterization

(2019) Jyoti S. Jha et al.   MATERIALS CHARACTERIZATION

Low cycle fatigue properties of Ti-6Al-4V alloy fabricated by high-power laser directed energy deposition: Experimental and prediction

(2019) Y.M. Ren et al.   INTERNATIONAL JOURNAL OF FATIGUE

Fatigue of additive manufactured Ti-6Al-4V, Part II: The relationship between microstructure, material cyclic properties, and component performance

(2019) R. Molaei et al.   INTERNATIONAL JOURNAL OF FATIGUE

Deformation and failure mechanisms of Ti–6Al–4V as built by selective laser melting

(2019) Atieh Moridi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Multiaxial fatigue behavior of wrought and additive manufactured Ti-6Al-4V including surface finish effect

(2017) Ali Fatemi et al.   INTERNATIONAL JOURNAL OF FATIGUE

Structural components manufactured by Selective Laser Melting and Investment Casting—Impact of the process route on the damage mechanism under cyclic loading

(2017) S. Leuders et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Cyclic plasticity and microstructure of as-built SLM Ti-6Al-4V: The effect of build orientation

(2017) Dylan Agius et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Crystallographic features of α variants and β phase for Ti-6Al-4V alloy fabricated by selective laser melting

(2017) Y. Yang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Additive Design and Manufacturing of Jet Engine Parts

(2017) Pinlian Han   Engineering

Critical assessment of the fatigue performance of additively manufactured Ti–6Al–4V and perspective for future research

(2016) P. Li et al.   INTERNATIONAL JOURNAL OF FATIGUE

Cyclic softening behavior of Ti–6Al–4V alloy at macro and micro-scale

(2016) Fengbo Han et al.   MATERIALS LETTERS

Comparison of the microstructures and mechanical properties of Ti–6Al–4V fabricated by selective laser melting and electron beam melting

(2016) Xiaoli Zhao et al.   MATERIALS & DESIGN

Anisotropic tensile behavior of Ti–6Al–4V components fabricated with directed energy deposition additive manufacturing

(2015) Beth E. Carroll et al.   ACTA MATERIALIA

Variant selection and intervariant crystallographic planes distribution in martensite in a Ti–6Al–4V alloy

(2014) Hossein Beladi et al.   ACTA MATERIALIA

Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V

(2014) M. Simonelli et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

On the Texture Formation of Selective Laser Melted Ti-6Al-4V

(2014) Marco Simonelli et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: Fatigue resistance and crack growth performance

(2012) S. Leuders et al.   INTERNATIONAL JOURNAL OF FATIGUE

Isothermal and thermomechanical fatigue behaviour of Ti–6Al–4V titanium alloy

(2011) Kartik Prasad et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Cyclic deformation response and micromechanisms of Ti alloy Ti–5Al–5V–5Mo–3Cr–0.5Fe

(2011) Jun Huang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of bulk damage on crack initiation in low-cycle fatigue of 316 stainless steel

(2010) M. KAMAYA   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

On characterization of deformation microstructure in Boron modified Ti–6Al–4V alloy

(2010) Shibayan Roy et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Oxidation of Ti–6Al–4V alloy

(2008) Hasan Guleryuz et al.   JOURNAL OF ALLOYS AND COMPOUNDS