Establishing specimen property to part performance relationships for laser beam powder bed fusion additive manufacturing

On the Relevance of Volumetric Energy Density in the Investigation of Inconel 718 Laser Powder Bed Fusion

(2020) Fabrizia Caiazzo et al.   Materials

Mechanical properties of diamond lattice Ti–6Al–4V structures produced by laser powder bed fusion: On the effect of the load direction

(2020) Antonio Cutolo et al.   Journal of the Mechanical Behavior of Biomedical Materials

Processing parameters in laser powder bed fusion metal additive manufacturing

(2020) J.P. Oliveira et al.   MATERIALS & DESIGN

Exploring the Correlation between Subsurface Residual Stresses and Manufacturing Parameters in Laser Powder Bed Fused Ti-6Al-4V

(2019) Tatiana Mishurova et al.   Metals

Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed x-ray imaging

(2019) Ross Cunningham et al.   SCIENCE

Fatigue behavior of additively manufactured 17-4 PH stainless steel: Synergistic effects of surface roughness and heat treatment

(2019) P.D. Nezhadfar et al.   INTERNATIONAL JOURNAL OF FATIGUE

A new FE post-processor for probabilistic fatigue assessment in the presence of defects and its application to AM parts

(2019) S. Romano et al.   INTERNATIONAL JOURNAL OF FATIGUE

An investigation into the effect of process parameters on melt pool geometry, cell spacing, and grain refinement during laser powder bed fusion

(2019) Ali Keshavarzkermani et al.   OPTICS AND LASER TECHNOLOGY

The Effects of Feature Sizes in Selectively Laser Melted Ti-6Al-4V Parts on the Validity of Optimised Process Parameters

(2019) Chinmay Phutela et al.   Materials

On the size and orientation effect in additive manufactured Ti-6Al-4V

(2019) D. Barba et al.   MATERIALS & DESIGN

Heat and fluid flow in additive manufacturing – Part II: Powder bed fusion of stainless steel, and titanium, nickel and aluminum base alloys

(2018) T. Mukherjee et al.   COMPUTATIONAL MATERIALS SCIENCE

Optimisation of process parameters to address fundamental challenges during selective laser melting of Ti-6Al-4V: A review

(2018) H. Shipley et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Scaling laws for the additive manufacturing

(2018) Alexander M. Rubenchik et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Additive manufacturing of fatigue resistant materials: Challenges and opportunities

(2017) Aref Yadollahi et al.   INTERNATIONAL JOURNAL OF FATIGUE

Fatigue Behavior and Modeling of Additively Manufactured Ti-6Al-4V Including Interlayer Time Interval Effects

(2017) Brian Torries et al.   JOM

Synchrotron-Based X-ray Microtomography Characterization of the Effect of Processing Variables on Porosity Formation in Laser Power-Bed Additive Manufacturing of Ti-6Al-4V

(2017) Ross Cunningham et al.   JOM

Progress Towards Metal Additive Manufacturing Standardization to Support Qualification and Certification

(2017) Mohsen Seifi et al.   JOM

On the limitations of Volumetric Energy Density as a design parameter for Selective Laser Melting

(2017) Umberto Scipioni Bertoli et al.   MATERIALS & DESIGN

Evaluating the Effect of Processing Parameters on Porosity in Electron Beam Melted Ti-6Al-4V via Synchrotron X-ray Microtomography

(2016) Ross Cunningham et al.   JOM

Correlation between porosity and processing parameters in TiAl6V4 produced by selective laser melting

(2016) Galina Kasperovich et al.   MATERIALS & DESIGN

Tailoring surface quality through mass and momentum transfer modeling using a volume of fluid method in selective laser melting of TiC/AlSi10Mg powder

(2015) Donghua Dai et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg

(2015) Christian Weingarten et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Effects of process time interval and heat treatment on the mechanical and microstructural properties of direct laser deposited 316L stainless steel

(2015) Aref Yadollahi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of defects on mechanical properties of Ti–6Al–4V components produced by selective laser melting and electron beam melting

(2015) Haijun Gong et al.   MATERIALS & DESIGN

Density of additively-manufactured, 316L SS parts using laser powder-bed fusion at powers up to 400 W

(2014) Chandrika Kamath et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing

(2014) Wayne E. King et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Parametric analysis of thermal behavior during selective laser melting additive manufacturing of aluminum alloy powder

(2014) Yali Li et al.   MATERIALS & DESIGN

Spatial variation of melt pool geometry, peak temperature and solidification parameters during laser assisted additive manufacturing process

(2014) V. Manvatkar et al.   MATERIALS SCIENCE AND TECHNOLOGY

Metal Fatigue Causing Cystoscope Rupture During Bladder Neck Incision

(2011) Alfonso Fernandez et al.   JSLS-Journal of the Society of Laparoendoscopic Surgeons