Evaluation of surface roughness and optimization of cutting parameters in turning of AA2024 alloy under different cooling-lubrication conditions using RSM method

The effect of vibration and cutting zone temperature on surface roughness and tool wear in eco-friendly MQL turning of AISI D2

(2020) Onur Özbek et al.   Journal of Materials Research and Technology-JMR&T

Ecological trends in machining as a key factor in sustainable production – A review

(2019) G.M. Krolczyk et al.   JOURNAL OF CLEANER PRODUCTION

Effects of reinforced nanoparticles with surfactant on surface quality and chip formation morphology in MQL-turning of superalloys

(2019) S.H. Musavi et al.   Journal of Manufacturing Processes

Effects of reinforced nanofluid with nanoparticles on cutting tool wear morphology

(2019) Seyed Hasan Musavi et al.   Journal of Central South University

Hybrid cryogenic MQL for improving tool life in machining of Ti-6Al-4V titanium alloy

(2019) Alborz Shokrani et al.   Journal of Manufacturing Processes

Tool Wear Morphology and Life under Various Lubrication Modes in Turning Stainless Steel 316L

(2019) Nader Barari et al.   TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING

Damage accumulation and crack initiation detection based on the evolution of surface roughness parameters

(2018) Ali Haghshenas et al.   INTERNATIONAL JOURNAL OF FATIGUE

Multi-objective optimization of parameters in turning of N-155 iron-nickel-base superalloy using gray relational analysis

(2018) Behzad Eskandari et al.   Journal of the Brazilian Society of Mechanical Sciences and Engineering

Solid Lubricant-assisted Minimum Quantity Lubrication and Cooling strategies to improve Ti6Al4V machinability in finishing turning

(2018) S. Sartori et al.   TRIBOLOGY INTERNATIONAL

Environmental-friendly turning of A286 superalloy

(2018) Seyed Hasan Musavi et al.   Journal of Manufacturing Processes

Analysis of the influence of cutting parameters on surface roughness and cutting forces in high speed face milling of Al/SiC MMC

(2018) Reza Ghoreishi et al.   Materials Research Express

Multi-objective optimization and life cycle assessment of eco-friendly cryogenic N2 assisted turning of Ti-6Al-4V

(2018) Mozammel Mia et al.   JOURNAL OF CLEANER PRODUCTION

To characterize and optimize the surface quality attributes in slot milling operation

(2017) Seyed Ali Niknam et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Sustainability in machining: “Eco-friendly” turning of Inconel 718. Surface characterisation and economic analysis

(2017) Vincenzo Tebaldo et al.   JOURNAL OF CLEANER PRODUCTION

Surface integrity and sustainability assessment in high-speed machining of Inconel 718 – An eco-friendly green approach

(2017) Ganesh S. Kadam et al.   JOURNAL OF CLEANER PRODUCTION

Influence factors and operational strategies for energy efficiency improvement of CNC machining

(2017) Lingling Li et al.   JOURNAL OF CLEANER PRODUCTION

Effects of Minimum Quantity Lubrication (MQL) in machining processes using conventional and nanofluid based cutting fluids: A comprehensive review

(2016) Anuj Kumar Sharma et al.   JOURNAL OF CLEANER PRODUCTION

Dry machining of nickel-based super alloy as a sustainable alternative using TiN/TiAlN coated tool

(2016) A. Thakur et al.   JOURNAL OF CLEANER PRODUCTION

Structural and Microhardness Changes After Turning of the AISI 1045 Steel for Minimum Quantity Cooling Lubrication

(2016) Radoslaw W. Maruda et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Effect of microscale texture on cutting performance of WC/Co-based TiAlN coated tools under different lubrication conditions

(2015) Kedong Zhang et al.   APPLIED SURFACE SCIENCE

Application of sustainable techniques in metal cutting for enhanced machinability: a review

(2015) Chetan et al.   JOURNAL OF CLEANER PRODUCTION

Tool wear mechanisms and multi-response optimization of tool life and volume of material removed in turning of N-155 iron–nickel-base superalloy using RSM

(2015) Behnam Davoodi et al.   MEASUREMENT

Effect of the local friction and contact nature on the Built-Up Edge formation process in machining ductile metals

(2015) S. Atlati et al.   TRIBOLOGY INTERNATIONAL

Experimental investigation on removing cutting fluid from turning of Inconel 725 with coated carbide tools

(2014) Ahmadreza Hosseini Tazehkandi et al.   JOURNAL OF CLEANER PRODUCTION

Performance of green machining: a comparative study of turning ductile cast iron FCD700

(2014) Jaharah A. Ghani et al.   JOURNAL OF CLEANER PRODUCTION

Experimental investigation and optimization of cutting parameters in dry and wet machining of aluminum alloy 5083 in order to remove cutting fluid

(2014) Behnam Davoodi et al.   JOURNAL OF CLEANER PRODUCTION

Experimental study on the effect of finishing parameters on surface roughness in magneto-rheological abrasive flow finishing process

(2014) Amir Dehghan Ghadikolaei et al.   PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE

The use of acoustic emission information to distinguish between dry and lubricated rolling element bearings in low-speed rotating machines

(2013) Seyed Ali Niknam et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Analysis of the evolution of the Built-Up Edge and Built-Up Layer formation mechanisms in the dry turning of aeronautical aluminium alloys

(2012) A. Gómez-Parra et al.   WEAR

A sustainable alternative for cooling the machining processes using a refrigerant fluid in recirculation inside the toolholder

(2011) G. C. Vicentin et al.   Clean Technologies and Environmental Policy

Dry machining of Inconel 718, workpiece surface integrity

(2011) A. Devillez et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Effects of minimum quantity lubrication on turning AISI 9310 alloy steel using vegetable oil-based cutting fluid

(2009) M.M.A. Khan et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Effects of cutting fluid application on tool wear in machining: Interactions with tool-coatings and tool surface features

(2009) Anshu D. Jayal et al.   WEAR