Structural and Microhardness Changes After Turning of the AISI 1045 Steel for Minimum Quantity Cooling Lubrication

Surface integrity analysis of abrasive water jet-cut surfaces of friction stir welded joints

(2016) Ratnesh Kumar et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Modeling of heat transfer conditions in cooling lubricant emulsions with low-boiling continuous media in narrow gaps

(2016) A.K. Rozentsvaig et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

A study on droplets sizes, their distribution and heat exchange for minimum quantity cooling lubrication (MQCL)

(2016) Radoslaw W. Maruda et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Effect of dynamic recrystallization at tool-chip interface on accelerating tool wear during high-speed cutting of AISI1045 steel

(2016) C.L. Pu et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Investigation of surface roughness, microhardness and white layer thickness in hard milling of AISI 4340 using minimum quantity lubrication

(2016) Hamed Hassanpour et al.   JOURNAL OF CLEANER PRODUCTION

Effect of spot continual induction hardening on the microstructure of steels: Comparison between AISI 1045 and 5140 steels

(2016) Kai Gao et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Optimization of cutting conditions for minimum residual stress, cutting force and surface roughness in end milling of S50C medium carbon steel

(2016) Nik Masmiati et al.   MEASUREMENT

Diagnostics of stator faults of the single-phase induction motor using thermal images, MoASoS and selected classifiers

(2016) Adam Glowacz et al.   MEASUREMENT

On the tribological behavior of retrieved hip femoral heads affected by metallic debris. A comparative investigation by stylus and optical profilometer for a new roughness measurement protocol

(2016) Massimiliano Merola et al.   MEASUREMENT

Morphology of Near- and Semispherical Melted Chips after the Grinding Processes Using Sol-Gel Abrasives Based on SEM-Imaging and Analysis

(2016) W. Kapłonek et al.   Advances in Materials Science and Engineering

Performance evaluation of Ti–6Al–4V grinding using chip formation and coefficient of friction under the influence of nanofluids

(2015) Dinesh Setti et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

An influence of active additives on the formation of selected indicators of the condition of the X10CrNi18-8 stainless steel surface layer in MQCL conditions

(2015) Radoslaw W. Maruda et al.   International Journal of Surface Science and Engineering

Influence of cooling conditions on the machining process under MQCL and MQL conditions

(2015) Radoslaw W. Maruda   Tehnicki Vjesnik-Technical Gazette

The Results Of Consolidation Of Sinters Being Deformed Under Complex Loading Condition

(2014) M. Rosiak   ARCHIVES OF METALLURGY AND MATERIALS

The transition to a clean, dry, and energy efficient polishing process: an innovative upgrade of abrasive flow machining for simultaneous generation of micro-geometry and polishing in the tooling industry

(2014) Franci Pusavec et al.   JOURNAL OF CLEANER PRODUCTION

Hard turning using HiPIMS-coated carbide tools: Wear behavior under dry and minimum quantity lubrication (MQL)

(2014) Satish Chinchanikar et al.   MEASUREMENT

Modeling of white layer thickness in high speed machining of hardened steel based on phase transformation mechanism

(2013) Chunzheng Duan et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Investigation of effects of dry and near dry machining on AISI D2 steel using vegetable oil

(2013) Jagdeep Sharma et al.   JOURNAL OF CLEANER PRODUCTION

Microhardness and Surface Integrity in Turning Process of Duplex Stainless Steel (DSS) for Different Cutting Conditions

(2013) G. Krolczyk et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Investigation on minimum quantity lubricant-MQL grinding of 100Cr6 hardened steel using different abrasive and coolant–lubricant types

(2010) T. Tawakoli et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Effect of cooling and lubrication conditions on surface topography and turning process of C45 steel

(2010) Tadeusz Leppert   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE