Evaluation of machinability and economic performance in cryogenic-assisted hard turning of α-β titanium: a step towards sustainable manufacturing
Published 2019 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
Evaluation of machinability and economic performance in cryogenic-assisted hard turning of α-β titanium: a step towards sustainable manufacturing
Authors
Keywords
-
Journal
MACHINING SCIENCE AND TECHNOLOGY
Volume -, Issue -, Pages 1-25
Publisher
Informa UK Limited
Online
2019-09-23
DOI
10.1080/10910344.2019.1652312
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Modeling and optimization of tool wear in MQL-assisted milling of Inconel 718 superalloy using evolutionary techniques
- (2018) GurRaj Singh et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Towards sustainability assessment of machining processes
- (2018) H.A. Hegab et al. JOURNAL OF CLEANER PRODUCTION
- Effects of duplex jets high-pressure coolant on machining temperature and machinability of Ti-6Al-4V superalloy
- (2018) Mozammel Mia et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Effect of time-controlled MQL pulsing on surface roughness in hard turning by statistical analysis and artificial neural network
- (2017) Mozammel Mia et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Study of surface roughness and cutting forces using ANN, RSM, and ANOVA in turning of Ti-6Al-4V under cryogenic jets applied at flank and rake faces of coated WC tool
- (2017) Mozammel Mia et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- The influence of cryogenic supercritical carbon dioxide cooling on tool wear during machining high thermal conductivity steel
- (2017) Tatang Mulyana et al. JOURNAL OF CLEANER PRODUCTION
- Evaluation of performance of nanofluid using multiwalled carbon nanotubes for machining of Ti–6AL–4V
- (2017) Neelesh Kumar Sahu et al. MACHINING SCIENCE AND TECHNOLOGY
- Performance enhancement of cryogenic machining and its effect on tool wear during turning of Al-Ticp composites
- (2017) Sravan Kumar Josyula et al. MACHINING SCIENCE AND TECHNOLOGY
- Comparative evaluations of machining performance during turning of 17-4 PH stainless steel under cryogenic and wet machining conditions
- (2017) P. Sivaiah et al. MACHINING SCIENCE AND TECHNOLOGY
- Multi-response optimization of end milling parameters under through-tool cryogenic cooling condition
- (2017) Mozammel Mia MEASUREMENT
- Effect of coating layer loss on the wear rate change of coated carbide tools in turning process
- (2017) Israel Martinez et al. PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY
- Cryogenic manufacturing processes
- (2016) I.S. Jawahir et al. CIRP ANNALS-MANUFACTURING TECHNOLOGY
- Comparative investigation on using cryogenic machining in CNC milling ofTi-6Al-4Vtitanium alloy
- (2016) Alborz Shokrani et al. MACHINING SCIENCE AND TECHNOLOGY
- Sustainable machining of titanium alloys: A critical review
- (2016) Kapil Gupta et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Tool wear and cost evaluation of face milling grade 5 titanium alloy for sustainable machining
- (2016) I. Masood et al. Advances in Production Engineering & Management
- Influence of High-Pressure Coolant Assistance on the Machinability of the Titanium AlloyTi555–3
- (2015) Tarek Braham-Bouchnak et al. MACHINING SCIENCE AND TECHNOLOGY
- Effect of cryogenic cooling on machinability and surface quality of bio-degradable ZK60 Mg alloy
- (2015) S. Dinesh et al. MATERIALS & DESIGN
- Evaluation of machining performance in cryogenic machining of Inconel 718 and comparison with dry and MQL machining
- (2014) Yusuf Kaynak INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Environmental friendly cutting fluids and cooling techniques in machining: a review
- (2014) Sujan Debnath et al. JOURNAL OF CLEANER PRODUCTION
- Investigation of effects of dry and near dry machining on AISI D2 steel using vegetable oil
- (2013) Jagdeep Sharma et al. JOURNAL OF CLEANER PRODUCTION
- Tool life and wear mechanisms in high speed machining of Ti–6Al–4V alloy with PCD tools under various coolant pressures
- (2013) Rosemar B. da Silva et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Tribological studies of potential vegetable oil-based lubricants containing environmentally friendly viscosity modifiers
- (2013) L.A. Quinchia et al. TRIBOLOGY INTERNATIONAL
- Tool-wear analysis in cryogenic machining of NiTi shape memory alloys: A comparison of tool-wear performance with dry and MQL machining
- (2013) Y. Kaynak et al. WEAR
- Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids
- (2012) A. Shokrani et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Application of vegetable oil-based metalworking fluids in machining ferrous metals—A review
- (2011) S.A. Lawal et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Machining of β-titanium-alloy Ti–10V–2Fe–3Al under cryogenic conditions: Cooling with carbon dioxide snow
- (2011) Christian Machai et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- AN ANALYSIS OF SURFACE INTEGRITY WHEN DRILLING INCONEL 718 USING PALM OIL AND SYNTHETIC ESTER UNDER MQL CONDITION
- (2011) Erween A. Rahim et al. MACHINING SCIENCE AND TECHNOLOGY
- Development of ecofriendly/biodegradable lubricants: An overview
- (2011) Ponnekanti Nagendramma et al. RENEWABLE & SUSTAINABLE ENERGY REVIEWS
- Surface integrity in cryogenic machining of nickel based alloy—Inconel 718
- (2010) F. Pusavec et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Cooling techniques for improved productivity in turning
- (2009) Vishal S. Sharma et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- A study of the microstructure and hardness of two titanium alloys: Commercially pure and Ti–6Al–4V
- (2009) N. Poondla et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Study on orthogonal turning of titanium alloys with different coolant supply strategies
- (2008) Z. G. Wang et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
Discover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversationCreate your own webinar
Interested in hosting your own webinar? Check the schedule and propose your idea to the Peeref Content Team.
Create Now