Effects of extreme pressure and anti-wear additives on surface topography and tool wear during MQCL turning of AISI 1045 steel

Surface quality and topographic inspection of variable compliance part after precise turning

(2018) P. Nieslony et al.   APPLIED SURFACE SCIENCE

Early fault diagnosis of bearing and stator faults of the single-phase induction motor using acoustic signals

(2018) Adam Glowacz et al.   MEASUREMENT

Application of signal to noise ratio and grey relational analysis to minimize forces and vibrations during precise ball end milling

(2018) Szymon Wojciechowski et al.   PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY

Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production

(2017) G.M. Krolczyk et al.   JOURNAL OF CLEANER PRODUCTION

Evaluation of the effects of machining parameters on MQL based surface grinding process using response surface methodology

(2017) Rahul R. Chakule et al.   Journal of Mechanical Science and Technology

Multi-sensor measurements of titanium alloy surface texture formed at subsequent operations of precision machining process

(2017) Magdalena Niemczewska-Wójcik   MEASUREMENT

Tool wear characterizations in finish turning of AISI 1045 carbon steel for MQCL conditions

(2017) Radoslaw W. Maruda et al.   WEAR

Modeling of heat transfer conditions in cooling lubricant emulsions with low-boiling continuous media in narrow gaps

(2016) A.K. Rozentsvaig et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Experimental method to analyze the oil mist impingement over an insert used in MQL milling process

(2016) Arnaud Duchosal et al.   MEASUREMENT

Surface morphology analysis of Duplex Stainless Steel (DSS) in Clean Production using the Power Spectral Density

(2016) G.M. Krolczyk et al.   MEASUREMENT

The influence of the cooling conditions on the cutting tool wear and the chip formation mechanism

(2016) Radoslaw W. Maruda et al.   Journal of Manufacturing Processes

Analysis of Contact Phenomena and Heat Exchange in the Cutting Zone Under Minimum Quantity Cooling Lubrication conditions

(2015) Radoslaw W. Maruda et al.   ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING

Performance evaluation of Ti–6Al–4V grinding using chip formation and coefficient of friction under the influence of nanofluids

(2015) Dinesh Setti et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

An influence of active additives on the formation of selected indicators of the condition of the X10CrNi18-8 stainless steel surface layer in MQCL conditions

(2015) Radoslaw W. Maruda et al.   International Journal of Surface Science and Engineering

Machining and ecological effects of a new developed cutting fluid in combination with different cooling techniques on turning operation

(2015) Yousef Shokoohi et al.   JOURNAL OF CLEANER PRODUCTION

Performance evaluation and optimization of nano boric acid powder weight percentage mixed with vegetable oil using the Taguchi approach

(2015) P. N. L. Pavani et al.   Journal of Mechanical Science and Technology

Influence of cooling conditions on the machining process under MQCL and MQL conditions

(2015) Radoslaw W. Maruda   Tehnicki Vjesnik-Technical Gazette

Estimating the effect of cutting data on surface roughness and cutting force during WC-Co turning with PCD tool using Taguchi design and ANOVA analysis

(2014) Wojciech Zębala et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Hard turning using HiPIMS-coated carbide tools: Wear behavior under dry and minimum quantity lubrication (MQL)

(2014) Satish Chinchanikar et al.   MEASUREMENT

Investigating the Minimum Quantity Lubrication in grinding of Al2O3 engineering ceramic

(2013) Mohsen Emami et al.   JOURNAL OF CLEANER PRODUCTION

Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids

(2012) A. Shokrani et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions

(2012) S. Zhang et al.   JOURNAL OF CLEANER PRODUCTION

Temperature and energy partition in minimum quantity lubrication-MQL grinding process

(2011) M.J. Hadad et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

A study on droplets and their distribution for minimum quantity lubrication (MQL)

(2010) Kyung-Hee Park et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Effect of cooling and lubrication conditions on surface topography and turning process of C45 steel

(2010) Tadeusz Leppert   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Transitioning to sustainable production – part II: evaluation of sustainable machining technologies

(2010) Franci Pusavec et al.   JOURNAL OF CLEANER PRODUCTION