Effects of extreme pressure and anti-wear additives on surface topography and tool wear during MQCL turning of AISI 1045 steel
出版年份 2018 全文链接
标题
Effects of extreme pressure and anti-wear additives on surface topography and tool wear during MQCL turning of AISI 1045 steel
作者
关键词
Cooling conditions, Surface analysis, Tool wear, Tribofilm
出版物
Journal of Mechanical Science and Technology
Volume 32, Issue 4, Pages 1585-1591
出版商
Springer Nature
发表日期
2018-04-18
DOI
10.1007/s12206-018-0313-7
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- Surface quality and topographic inspection of variable compliance part after precise turning
- (2018) P. Nieslony et al. APPLIED SURFACE SCIENCE
- Early fault diagnosis of bearing and stator faults of the single-phase induction motor using acoustic signals
- (2018) Adam Glowacz et al. MEASUREMENT
- Application of signal to noise ratio and grey relational analysis to minimize forces and vibrations during precise ball end milling
- (2018) Szymon Wojciechowski et al. PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY
- Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production
- (2017) G.M. Krolczyk et al. JOURNAL OF CLEANER PRODUCTION
- Evaluation of the effects of machining parameters on MQL based surface grinding process using response surface methodology
- (2017) Rahul R. Chakule et al. Journal of Mechanical Science and Technology
- Multi-sensor measurements of titanium alloy surface texture formed at subsequent operations of precision machining process
- (2017) Magdalena Niemczewska-Wójcik MEASUREMENT
- Tool wear characterizations in finish turning of AISI 1045 carbon steel for MQCL conditions
- (2017) Radoslaw W. Maruda et al. WEAR
- Modeling of heat transfer conditions in cooling lubricant emulsions with low-boiling continuous media in narrow gaps
- (2016) A.K. Rozentsvaig et al. INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER
- Experimental method to analyze the oil mist impingement over an insert used in MQL milling process
- (2016) Arnaud Duchosal et al. MEASUREMENT
- Surface morphology analysis of Duplex Stainless Steel (DSS) in Clean Production using the Power Spectral Density
- (2016) G.M. Krolczyk et al. MEASUREMENT
- The influence of the cooling conditions on the cutting tool wear and the chip formation mechanism
- (2016) Radoslaw W. Maruda et al. Journal of Manufacturing Processes
- Analysis of Contact Phenomena and Heat Exchange in the Cutting Zone Under Minimum Quantity Cooling Lubrication conditions
- (2015) Radoslaw W. Maruda et al. ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING
- Performance evaluation of Ti–6Al–4V grinding using chip formation and coefficient of friction under the influence of nanofluids
- (2015) Dinesh Setti et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- An influence of active additives on the formation of selected indicators of the condition of the X10CrNi18-8 stainless steel surface layer in MQCL conditions
- (2015) Radoslaw W. Maruda et al. International Journal of Surface Science and Engineering
- Machining and ecological effects of a new developed cutting fluid in combination with different cooling techniques on turning operation
- (2015) Yousef Shokoohi et al. JOURNAL OF CLEANER PRODUCTION
- Performance evaluation and optimization of nano boric acid powder weight percentage mixed with vegetable oil using the Taguchi approach
- (2015) P. N. L. Pavani et al. Journal of Mechanical Science and Technology
- Influence of cooling conditions on the machining process under MQCL and MQL conditions
- (2015) Radoslaw W. Maruda Tehnicki Vjesnik-Technical Gazette
- Estimating the effect of cutting data on surface roughness and cutting force during WC-Co turning with PCD tool using Taguchi design and ANOVA analysis
- (2014) Wojciech Zębala et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Hard turning using HiPIMS-coated carbide tools: Wear behavior under dry and minimum quantity lubrication (MQL)
- (2014) Satish Chinchanikar et al. MEASUREMENT
- Investigating the Minimum Quantity Lubrication in grinding of Al2O3 engineering ceramic
- (2013) Mohsen Emami et al. JOURNAL OF CLEANER PRODUCTION
- Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids
- (2012) A. Shokrani et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions
- (2012) S. Zhang et al. JOURNAL OF CLEANER PRODUCTION
- Temperature and energy partition in minimum quantity lubrication-MQL grinding process
- (2011) M.J. Hadad et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- A study on droplets and their distribution for minimum quantity lubrication (MQL)
- (2010) Kyung-Hee Park et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Effect of cooling and lubrication conditions on surface topography and turning process of C45 steel
- (2010) Tadeusz Leppert INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Transitioning to sustainable production – part II: evaluation of sustainable machining technologies
- (2010) Franci Pusavec et al. JOURNAL OF CLEANER PRODUCTION
Discover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversationAdd your recorded webinar
Do you already have a recorded webinar? Grow your audience and get more views by easily listing your recording on Peeref.
Upload Now