- Home
- Publications
- Publication Search
- Publication Details
Title
Key factors of stretch-flangeability of sheet materials
Authors
Keywords
Fracture Toughness, Fracture Energy, Digital Image Correlation, Sheet Material, Fracture Toughness Test
Journal
JOURNAL OF MATERIALS SCIENCE
Volume 52, Issue 13, Pages 7808-7823
Publisher
Springer Nature
Online
2017-03-20
DOI
10.1007/s10853-017-1012-y
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Formation and growth of voids in dual-phase steel at microscale and nanoscale levels
- (2017) Gregory Gerstein et al. JOURNAL OF MATERIALS SCIENCE
- Phase transformation and mechanical behaviour of thermo-mechanically controlled processed high-strength multiphase steel
- (2016) G. Mandal et al. JOURNAL OF MATERIALS SCIENCE
- Obtaining Reliable True Plastic Stress-Strain Curves in a Wide Range of Strains Using Digital Image Correlation in Tensile Testing
- (2016) Hyoung Seop Kim et al. Korean Journal of Metals and Materials
- Correlation between fracture toughness and stretch-flangeability of advanced high strength steels
- (2016) Jae Ik Yoon et al. MATERIALS LETTERS
- Fracture toughness characterization through notched small punch test specimens
- (2016) Emilio Martínez-Pañeda et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Factors governing hole expansion ratio of steel sheets with smooth sheared edge
- (2016) Jae Ik Yoon et al. METALS AND MATERIALS INTERNATIONAL
- Effect of punch speed on the formability behavior of austenitic stainless steel type 304L
- (2016) H. Fathi et al. METALS AND MATERIALS INTERNATIONAL
- Effects of Coiling Temperature and Carbides Behavior on Stretch-flangeability for 980 MPa Hot-rolled Steels
- (2016) Namhyun Kang et al. Korean Journal of Metals and Materials
- Novel ultra-high-strength (ferrite + austenite) duplex lightweight steels achieved by fine dislocation substructures (Taylor lattices), grain refinement, and partial recrystallization
- (2015) Seok Su Sohn et al. ACTA MATERIALIA
- An Overview of Dual-Phase Steels: Advances in Microstructure-Oriented Processing and Micromechanically Guided Design
- (2015) C.C. Tasan et al. Annual Review of Materials Research
- Effect of C content on the microstructure and tensile properties of lightweight ferritic Fe-8Al-5Mn-0.1Nb alloy
- (2015) A. Zargaran et al. METALS AND MATERIALS INTERNATIONAL
- Novel ferrite–austenite duplex lightweight steel with 77% ductility by transformation induced plasticity and twinning induced plasticity mechanisms
- (2014) Seok Su Sohn et al. ACTA MATERIALIA
- Forming limit criterion for ductile anisotropic sheets as a material property and its deformation path insensitivity, Part II: Boundary value problems
- (2014) Kwansoo Chung et al. INTERNATIONAL JOURNAL OF PLASTICITY
- Forming limit criterion for ductile anisotropic sheets as a material property and its deformation path insensitivity. Part I: Deformation path insensitive formula based on theoretical models
- (2014) Kwansoo Chung et al. INTERNATIONAL JOURNAL OF PLASTICITY
- Non-linear Correlation Between Uniaxial Tensile Properties and Shear-Edge Hole Expansion Ratio
- (2014) Surajit Kumar Paul JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
- The effect of processing parameters on the microstructure and mechanical properties of low-Si transformation-induced plasticity steels
- (2014) Fayez Alharbi et al. JOURNAL OF MATERIALS SCIENCE
- Effect of the Tempered Martensite Matrix and Granular Bainite on Stretch-Flangeability for 980 MPa Hot-Rolled Steel
- (2014) Juseung Lee et al. Korean Journal of Metals and Materials
- Study of curvature and pre-damage effects on the edge stretchability of advanced high strength steel based on a new simulation model
- (2014) Chenjue Ye et al. International Journal of Material Forming
- The micromechanical deformation behaviors of hot-rolled 590FB steel during hole-expansion test
- (2013) S.-H. Choi et al. INTERNATIONAL JOURNAL OF PLASTICITY
- Experimental and numerical investigation of Mg alloy sheet formability
- (2013) M. Nebebe Mekonen et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Advanced high strength steels for automotive industry
- (2012) R. KUZIAK et al. Archives of Civil and Mechanical Engineering
- Influence of Ti and Nb on the Strength–Ductility–Hole Expansion Ratio Balance of Hot-rolled Low-carbon High-strength Steel Sheets
- (2012) Kyohei Kamibayashi et al. ISIJ INTERNATIONAL
- Development of hot rolled steel sheet with 600MPa UTS for automotive wheel application
- (2012) Gajendra Jha et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Effect of micro-alloying elements on the stretch-flangeability of dual phase steel
- (2012) Jewoong Lee et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Design and development of precipitate strengthened advanced high strength steel for automotive application
- (2012) Gajendra Jha et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Design for sustainability in automotive industry: A comprehensive review
- (2012) Ahmad Mayyas et al. RENEWABLE & SUSTAINABLE ENERGY REVIEWS
- Hole expansion of twinning-induced plasticity steel
- (2012) Le Xu et al. SCRIPTA MATERIALIA
- A finite element ductile failure simulation method using stress-modified fracture strain model
- (2010) Chang-Sik Oh et al. ENGINEERING FRACTURE MECHANICS
- Stretch-Flangeability of High Mn TWIP steel
- (2010) L. Chen et al. STEEL RESEARCH INTERNATIONAL
- Mechanical anisotropy and deep drawing behaviour of AZ31 and ZE10 magnesium alloy sheets
- (2009) Sangbong Yi et al. ACTA MATERIALIA
- Application of extended Mohr–Coulomb criterion to ductile fracture
- (2009) Yuanli Bai et al. INTERNATIONAL JOURNAL OF FRACTURE
- Relationship between stretch formability and work-hardening capacity of twin-roll cast Mg alloys at room temperature
- (2009) D.H. Kang et al. SCRIPTA MATERIALIA
- Theoretical and numerical study of strain rate influence on AA5083 formability
- (2008) Cunsheng Zhang et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Measuring the predictive accuracy of various models of formability of Corus Tubular Blanks
- (2008) M. Evans JOURNAL OF MATERIALS SCIENCE
- The effect of strain rate sensitivity on theoretical prediction of limiting draw ratio for cylindrical cup drawing process
- (2006) R. Narayanasamy et al. MATERIALS & DESIGN
Add your recorded webinar
Do you already have a recorded webinar? Grow your audience and get more views by easily listing your recording on Peeref.
Upload NowAsk a Question. Answer a Question.
Quickly pose questions to the entire community. Debate answers and get clarity on the most important issues facing researchers.
Get Started