Factors governing hole expansion ratio of steel sheets with smooth sheared edge
Published 2016 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
Factors governing hole expansion ratio of steel sheets with smooth sheared edge
Authors
Keywords
metals, deformation, mechanical properties, tensile test, stretch-flangeability
Journal
METALS AND MATERIALS INTERNATIONAL
Volume 22, Issue 6, Pages 1009-1014
Publisher
Springer Nature
Online
2016-10-29
DOI
10.1007/s12540-016-6346-5
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Effects of Coiling Temperature and Carbides Behavior on Stretch-flangeability for 980 MPa Hot-rolled Steels
- (2016) Namhyun Kang et al. Korean Journal of Metals and Materials
- Effect of Preheating on Weldability and Corrosion Resistance in 690 MPa Grade Quenched and Tempered Steel weld metals
- (2016) Hae-Woo Lee et al. Korean Journal of Metals and Materials
- Novel ultra-high-strength (ferrite + austenite) duplex lightweight steels achieved by fine dislocation substructures (Taylor lattices), grain refinement, and partial recrystallization
- (2015) Seok Su Sohn et al. ACTA MATERIALIA
- FE simulation of edge fracture considering pre-damage from blanking process
- (2015) Kai Wang et al. INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES
- Oxidation of High Mn TWIP Steels in Reheating Furnace Conditions
- (2015) Dong Bok Lee et al. Korean Journal of Metals and Materials
- Suppression of dislocations at high strain rate deformation in a twinning-induced plasticity steel
- (2015) Z.Y. Liang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Strain hardening rate sensitivity and strain rate sensitivity in TWIP steels
- (2015) Alexandra Bintu et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Non-linear Correlation Between Uniaxial Tensile Properties and Shear-Edge Hole Expansion Ratio
- (2014) Surajit Kumar Paul JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
- Effect of the Tempered Martensite Matrix and Granular Bainite on Stretch-Flangeability for 980 MPa Hot-Rolled Steel
- (2014) Juseung Lee et al. Korean Journal of Metals and Materials
- Effect of Strength Grades of Dual Phase Steels on Failure Location and Joint Efficiency of GMAW Lap Joints
- (2014) Jae Won Kim Korean Journal of Metals and Materials
- Effect of Deformation Twin on Mechanical Properties of a Lean Manganese Twinning Induced Plasticity (TWIP) Steel Deformed at Quasi-Static Strain Rates
- (2014) Byeong-Hwan Song et al. Korean Journal of Metals and Materials
- Evaluation of Fire Resistance for H-Section Columns Made of Rolled Steels for General Structures and for Welded Structures by Analytic Method
- (2014) In-Kyu Kwon Korean Journal of Metals and Materials
- Effects of intergranular carbide precipitation on delayed fracture behavior in three TWinning Induced Plasticity (TWIP) steels
- (2013) Seokmin Hong et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Serration Phenomena Occurring During Tensile Tests of Three High-Manganese Twinning-Induced Plasticity (TWIP) Steels
- (2013) Seokmin Hong et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Influence of Ti and Nb on the Strength–Ductility–Hole Expansion Ratio Balance of Hot-rolled Low-carbon High-strength Steel Sheets
- (2012) Kyohei Kamibayashi et al. ISIJ INTERNATIONAL
- Effect of micro-alloying elements on the stretch-flangeability of dual phase steel
- (2012) Jewoong Lee et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Effects of Aluminum Addition on Tensile and Cup Forming Properties of Three Twinning Induced Plasticity Steels
- (2012) Seokmin Hong et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Effects of Inclusions on Delayed Fracture Properties of Three TWinning Induced Plasticity (TWIP) Steels
- (2012) Seokmin Hong et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Design for sustainability in automotive industry: A comprehensive review
- (2012) Ahmad Mayyas et al. RENEWABLE & SUSTAINABLE ENERGY REVIEWS
- Hole expansion of twinning-induced plasticity steel
- (2012) Le Xu et al. SCRIPTA MATERIALIA
- On the origin of dynamic strain aging in twinning-induced plasticity steels
- (2011) Seok-Jae Lee et al. ACTA MATERIALIA
- Application of extended Mohr–Coulomb criterion to ductile fracture
- (2009) Yuanli Bai et al. INTERNATIONAL JOURNAL OF FRACTURE
- On the Tensile Behavior of High-Manganese Twinning-Induced Plasticity Steel
- (2009) Jin-Kyung Kim et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
Find Funding. Review Successful Grants.
Explore over 25,000 new funding opportunities and over 6,000,000 successful grants.
ExploreDiscover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversation