oiInfluence of uniaxial and equi-biaxial tensile pre-straining on the high cycle and notch fatigue behaviour of AA2024-T4 aluminium alloy

A cyclic plastic zone size-based defect tolerant design approach to predict the fatigue life of additively manufactured alloys

(2023) Surajit Kumar Paul   Forces in Mechanics

The influence of equi-biaxial and uniaxial tensile pre-strain on the low cycle fatigue performance of the AA2024-T4 aluminium alloy

(2023) Amit Vikram Rex et al.   International Journal of Fatigue

Influence of pre-straining on the low-cycle fatigue performance of Fe–0.1C–5Mn medium manganese steel

(2022) Mei Zhang et al.   INTERNATIONAL JOURNAL OF FATIGUE

A computationally fast and accurate procedure for the identification of the Chaboche isotropic-kinematic hardening model parameters based on strain-controlled cycles and asymptotic ratcheting rate

(2022) C. Santus et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Influence of uniaxial and biaxial pre-straining on the low cycle fatigue performance of DP590 steel

(2021) Puja Ghosal et al.   INTERNATIONAL JOURNAL OF FATIGUE

Multiscale study of cold-rolling deformation on mechanical and corrosion behaviors of AA2024-T4 aluminum alloy

(2021) Sofia Benamirouche et al.   JOURNAL OF THE INDIAN CHEMICAL SOCIETY

Effects of pre-strain on the surface residual stress and corrosion behavior of an Al-Zn-Mg-Cu alloy plate

(2020) Lianghua Lin et al.   MATERIALS CHARACTERIZATION

Effect of tensile pre-strain on low-cycle fatigue behaviour of 7050-T6 aluminium alloy

(2020) R. Branco et al.   ENGINEERING FAILURE ANALYSIS

XRD structural studies on cobalt doped zinc oxide nanoparticles synthesized by coprecipitation method: Williamson-Hall and size-strain plot approaches

(2020) P. Shunmuga Sundaram et al.   PHYSICA B-CONDENSED MATTER

Determination of Chaboche combined hardening parameters with dual backstress for ratcheting evaluation of AISI 52100 bearing steel

(2019) Sungyong Koo et al.   INTERNATIONAL JOURNAL OF FATIGUE

Influence of microstructure and strain rate on the strain partitioning behaviour of dual phase steels

(2019) Anindya Das et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of pre-straining path on high cycle fatigue performance of DP 600 steel

(2019) Bimal Das et al.   INTERNATIONAL JOURNAL OF FATIGUE

Energy field intensity approach for notch fatigue analysis

(2019) Ding Liao et al.   INTERNATIONAL JOURNAL OF FATIGUE

Low cycle fatigue performance of DP600 steel under various pre-straining paths

(2019) Bimal Das et al.   INTERNATIONAL JOURNAL OF FATIGUE

Recent advances in the development of aerospace materials

(2018) Xuesong Zhang et al.   PROGRESS IN AEROSPACE SCIENCES

Crack Propagation Mechanisms for Creep Fatigue: A Consolidated Explanation of Fundamental Behaviours from Initiation to Failure

(2018) Dan Liu et al.   Metals

Sensitivity and optimisation of the Chaboche plasticity model parameters in strain-life fatigue predictions

(2017) Dylan Agius et al.   MATERIALS & DESIGN

A comparison of EBSD based strain indicators for the study of Fe-3Si steel subjected to cyclic loading

(2016) Claire Schayes et al.   MATERIALS CHARACTERIZATION

Lifetime prediction in medium-cycle fatigue regime of notched specimens

(2016) R. Negru et al.   THEORETICAL AND APPLIED FRACTURE MECHANICS

Strain-induced damage of metals under large plastic deformation: Theoretical framework and experiments

(2014) Nikolai Tutyshkin et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Effects of pre-strain on uniaxial ratcheting and fatigue failure of Z2CN18.10 austenitic stainless steel

(2013) Yong Wang et al.   INTERNATIONAL JOURNAL OF FATIGUE

Proportional and non-proportional hardening behavior of dual-phase steels

(2013) Li Sun et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Recent developments in advanced aircraft aluminium alloys

(2013) Tolga Dursun et al.   MATERIALS & DESIGN

Effect of prestrain on tensile properties and ratcheting behaviour of Ti-stabilised interstitial free steel

(2013) Partha Sarathi De et al.   MATERIALS & DESIGN

Strain hardening response and modeling of EDDQ and DP780 steel sheet under non-linear strain path

(2013) Jinjin Ha et al.   MECHANICS OF MATERIALS

Fatigue strength of Al7075 notched plates based on the local SED averaged over a control volume

(2013) Filippo Berto et al.   Science China-Physics Mechanics & Astronomy

A study of the heterogeneity of plastic deformation in IF steel by EBSD

(2012) Nathalie Allain-Bonasso et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

A Review of Strain Analysis Using Electron Backscatter Diffraction

(2011) Stuart I. Wright et al.   MICROSCOPY AND MICROANALYSIS

Simulation of cyclic plastic deformation response in SA333 C–Mn steel by a kinematic hardening model

(2010) Surajit Kumar Paul et al.   COMPUTATIONAL MATERIALS SCIENCE

Assessment of methods for prediction of notch and size effects at the fatigue limit based on test data by Böhm and Magin

(2010) G. Härkegård et al.   INTERNATIONAL JOURNAL OF FATIGUE

Tensile and Fatigue Behavior of Friction-Stir Welded Tailor-Welded Blank of Aluminum Alloy 5754

(2010) M. Garware et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Influence of asymmetric cyclic loading on substructure formation and ratcheting fatigue behaviour of AISI 304LN stainless steel

(2010) K. Dutta et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

How complex is the microstructure of AA2024-T3?

(2009) A. Boag et al.   CORROSION SCIENCE

Creep damage assessment of 10Cr-1Mo-1W-VNbN steel forging through EBSD observation

(2009) Kazunari Fujiyama et al.   INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING

The theory of critical distances

(2007) D. Taylor   ENGINEERING FRACTURE MECHANICS

Influence of large pre-straining of aluminium alloys on their residual fatigue resistance

(2007) C FROUSTEY et al.   INTERNATIONAL JOURNAL OF FATIGUE