Rapid grain refinement and compositional homogenization in a cast binary Cu50Ni alloy achieved by friction stir processing

Heterogenous activation of dynamic recrystallization and twinning during friction stir processing of a Cu-4Nb alloy

(2022) Julian Escobar et al.   JOURNAL OF ALLOYS AND COMPOUNDS

A theoretical calculation of stacking fault energy of Ni alloys: The effects of temperature and composition

(2021) Mohammad S. Dodaran et al.   COMPUTATIONAL MATERIALS SCIENCE

Achieving high strength-ductility in pure copper by cold rolling and submerged friction stir processing (SFSP)

(2021) Hoora Mazaheri et al.   Journal of Manufacturing Processes

Multimodal analysis of spatially heterogeneous microstructural refinement and softening mechanisms in three-pass friction stir processed Al-4Si alloy

(2021) Julian Escobar et al.   JOURNAL OF ALLOYS AND COMPOUNDS

The onset of alloying in Cu-Ni powders under high-shear consolidation

(2021) N.R. Overman et al.   MATERIALS & DESIGN

Effect of Stacking Fault Energy on the Grain Structure Evolution of FCC Metals During Friction Stir Welding

(2020) Xiaochao Liu et al.   Acta Metallurgica Sinica-English Letters

Residual stress characterization in friction stir welds of alloy 625

(2019) Guilherme Vieira Braga Lemos et al.   Journal of Materials Research and Technology-JMR&T

High-resolution EBSD characterisation of friction stir welded nickel–copper alloy: effect of the initial microstructure on microstructural evolution and mechanical properties

(2019) Akbar Heidarzadeh et al.   PHILOSOPHICAL MAGAZINE

Understanding precipitate evolution during friction stir welding of Al-Zn-Mg-Cu alloy through in-situ measurement coupled with simulation

(2018) J.F. dos Santos et al.   ACTA MATERIALIA

Twenty-year uninterrupted endeavor of friction stir processing by focusing on copper and its alloys

(2018) M. Ebrahimi et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Effects of different friction stir welding conditions on the microstructure and mechanical properties of copper plates

(2016) Ali Alavi Nia et al.   International Journal of Minerals Metallurgy and Materials

Microstructure and mechanical properties of friction stir processed Cu with an ideal ultrafine-grained structure

(2016) P. Xue et al.   MATERIALS CHARACTERIZATION

A review of dynamic recrystallization phenomena in metallic materials

(2016) K. Huang et al.   MATERIALS & DESIGN

Characterization of residual stress as a function of friction stir welding parameters in oxide dispersion strengthened (ODS) steel MA956

(2015) L.N. Brewer et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructural evolution of pure copper during friction-stir welding

(2015) S. Mironov et al.   PHILOSOPHICAL MAGAZINE

Formation of annealing twins during primary recrystallization of two low stacking fault energy Ni-based alloys

(2014) W. Wang et al.   JOURNAL OF MATERIALS SCIENCE

Twinning in copper deformed at high strain rates

(2013) S CRONJE et al.   BULLETIN OF MATERIALS SCIENCE

Evaluation of Tensile Deformation Properties of Friction Stir Processed Pure Copper: Effect of Processing Parameters and Pass Number

(2013) Mohsen Barmouz et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Achieving ultrafine-grained structure in a pure nickel by friction stir processing with additional cooling

(2013) P. Xue et al.   MATERIALS & DESIGN

Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions

(2013) Taku Sakai et al.   PROGRESS IN MATERIALS SCIENCE

The influence of multi-pass friction stir processing on the microstructural and mechanical properties of Aluminum Alloy 6082

(2012) Magdy M. El-Rayes et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Multipass Friction-Stir Processing and its Effect on Mechanical Properties of Aluminum Alloy 5086

(2012) K. N. Ramesh et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Improved representations of misorientation information for grain boundary science and engineering

(2012) Srikanth Patala et al.   PROGRESS IN MATERIALS SCIENCE

Quantification of the microstructures of high purity nickel subjected to dynamic plastic deformation

(2011) Z.P. Luo et al.   ACTA MATERIALIA

Shear induced chemical mixing in heterogeneous systems

(2011) Yinon Ashkenazy et al.   ACTA MATERIALIA

Friction stir processing of direct metal deposited copper–nickel 70/30

(2011) S. Mukherjee et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Development of nanocrystalline structure in Cu during friction stir processing (FSP)

(2011) Jian-Qing Su et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Grain detection from 2d and 3d EBSD data—Specification of the MTEX algorithm

(2011) Florian Bachmann et al.   ULTRAMICROSCOPY