Experimental investigation on mechanical strength of adhesively bonded 3D-printed joints under hygrothermal conditions using Taguchi method

Multi-objective crashworthiness optimization of square aluminum tubes with functionally graded BCC lattice structure filler

(2023) Cengiz Baykasoğlu et al.   INTERNATIONAL JOURNAL OF CRASHWORTHINESS

Effects of steps on the load bearing capacity of 3D-printed single lap joints

(2023) Mohammad Reza Khosravani et al.   Journal of Materials Research and Technology-JMR&T

Digital design and manufacturing of spherical joint base on multi-objective topology optimization and 3D printing

(2023) Q.C. Xin et al.   Structures

Numerical simulation and failure experiment of hygrothermal aged CFRP single and double lap joints

(2023) Hongli Chen et al.   THIN-WALLED STRUCTURES

Improvement of structural, thermal and mechanical properties of epoxy composites and bonded joints exposed to water environment by incorporating boron nanoparticles

(2022) Yasemin Korkmaz et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

The effect of boron nanoparticle reinforcement on the structural and mechanical performance of nanocomposites and bonded joints exposed to an acid environment

(2022) Kürşat Gülteki̇n et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

The effect of hygrothermal aging on the adhesion performance of nanomaterial reinforced aluminium adhesive joints

(2022) Reyhan Ceylan et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Effects of hygrothermal ageing and temperature on the mechanical behavior of aluminum-CFRP hybrid (riveted/bonded) joints

(2022) Hanyu Zhang et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Investigating the failure behavior of hygrothermally aged adhesively bonded CFRP-aluminum alloy joints using modified Arcan fixture

(2022) WenLong Mu et al.   THIN-WALLED STRUCTURES

Loading-rate effect on tensile and bending strength of 3D-printed polylactic acid adhesively bonded joints

(2021) M. Gokhan Atahan et al.   JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY

Structural integrity of adhesively bonded 3D-printed joints

(2021) Mohammad Reza Khosravani et al.   POLYMER TESTING

Experimental analysis of manufacturing parameters’ effect on the flexural properties of wood-PLA composite parts built through FFF

(2020) M. Damous Zandi et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Effect of hygrothermal-mechanical exposure on the residual strength of adhesively bonded joints

(2020) Jian Li et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Effect of low-velocity impact on the strength and durability of bonded joint in hygrothermal environment

(2020) Jian Li et al.   JOURNAL OF ADHESION

An overview of manufacturing functionally graded adhesives – Challenges and prospects

(2019) J.B. Marques et al.   JOURNAL OF ADHESION

OPTIMIZATION OF THE MACHINING PARAMETERS IN TURNING OF HARDENED HOT WORK TOOL STEEL USING CRYOGENICALLY TREATED TOOLS

(2019) ENGIN NAS et al.   SURFACE REVIEW AND LETTERS

Structural relationships and optimization of resin-finishing parameters using the Taguchi approach

(2018) Faizan Shafiq et al.   CELLULOSE

Durability of adhesively bonded joints between pultruded GFRP adherends under hygrothermal and natural ageing

(2018) J.M. Sousa et al.   COMPOSITES PART B-ENGINEERING

Effect of alternating load on the residual strength of environmentally aged adhesively bonded CFRP-aluminum alloy joints

(2018) Wenlong Mu et al.   COMPOSITES PART B-ENGINEERING

Functionally graded adhesive joints – A review and prospects

(2017) J.F. Durodola   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Strength prediction of adhesively bonded single lap joints with different bondline thicknesses: A critical longitudinal strain approach

(2017) A. Akhavan-Safar et al.   INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES

Effect of layer thickness and print orientation on strength of 3D printed and adhesively bonded single lap joints

(2017) Volkan Kovan et al.   Journal of Mechanical Science and Technology

Effect of grooved pin-fins in a rectangular channel on heat transfer augmentation and friction factor using Taguchi method

(2016) M. Eren et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Adhesive bonding of 3D-printed ABS parts and wood

(2016) Mirko Kariz et al.   JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY

Experimental study of strain rate effects on the strength of adhesively bonded joints after hygrothermal exposure

(2015) Fan Zhang et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Regularization of torsional stresses in tubular lap bonded joints by means of functionally graded adhesives

(2014) A. Spaggiari et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Optimization of surface roughness and flank wear using the Taguchi method in milling of Hadfield steel with PVD and CVD coated inserts

(2014) Turgay Kıvak   MEASUREMENT

Experimental study of initial strengths and hygrothermal degradation of adhesive joints between thin aluminum and steel substrates

(2013) Fan Zhang et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Effect of Mechanical Surface Treatment on the Static Strength of Adhesive Lap Joints

(2013) A. Spaggiari et al.   The Journal of Adhesion

Experimental Tests on Tubular Bonded Butt Specimens: Effect of Relief Grooves on Tensile Strength of the Adhesive

(2012) A. Spaggiari et al.   The Journal of Adhesion

Evaluation of vegetable based cutting fluids with extreme pressure and cutting parameters in turning of AISI 304L by Taguchi method

(2011) M. Huseyin Cetin et al.   JOURNAL OF CLEANER PRODUCTION

Effect of grooves on the strength of adhesively bonded joints

(2010) Lucas F.M. da Silva et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Robust Shape Optimization of Tubular Butt Joints for Characterizing Thin Adhesive Layers under Uniform Normal and Shear Stresses

(2010) D. Castagnetti et al.   JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY