Evaluation of hole quality to explore the influence of graphene nanoplatelets embedded in epoxy/carbon composite during abrasive water jet drilling
Published 2022 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
Evaluation of hole quality to explore the influence of graphene nanoplatelets embedded in epoxy/carbon composite during abrasive water jet drilling
Authors
Keywords
-
Journal
Journal of Manufacturing Processes
Volume 85, Issue -, Pages 569-583
Publisher
Elsevier BV
Online
2022-12-08
DOI
10.1016/j.jmapro.2022.11.054
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Influence of fillers on polymeric composite during conventional machining processes: a review
- (2021) R. K. Thakur et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Study on delamination factor and surface roughness in abrasive water jet drilling of carbon fiber-reinforced polymer composites with different fiber orientation angles
- (2021) Meltem Altin Karataş et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Experimental investigation and optimization of abrasive waterjet machining parameters for GFRP composites using metaphor-less algorithms
- (2021) Dharmagna R. Tripathi et al. MATERIALS AND MANUFACTURING PROCESSES
- Impact of nanoclay filler reinforcement on CFRP composite performance during abrasive water jet machining
- (2021) R. K. Thakur et al. MATERIALS AND MANUFACTURING PROCESSES
- Experimental analysis on carbon nanotube embedded GFRP composites during AWJM
- (2021) Kalyan Kumar Singh et al. MATERIALS AND MANUFACTURING PROCESSES
- Damage study of fiber-reinforced composites drilled by abrasive waterjet —challenges and opportunities
- (2021) Yifei Zhang et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Optimization of machining parameters for kerf angle and roundness error in abrasive water jet drilling of CFRP composites with different fiber orientation angles
- (2020) Meltem Altin Karataş et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Abrasive waterjet machining of fiber-reinforced composites: a state-of-the-art review
- (2020) R. K. Thakur et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- The fatigue of carbon fibre reinforced plastics - A review
- (2019) Parvez Alam et al. COMPOSITES PART B-ENGINEERING
- Effect of pristine MWCNTs on the fatigue life of GFRP laminates-an experimental and statistical evaluation
- (2019) Anand Gaurav et al. COMPOSITES PART B-ENGINEERING
- Experimental study on hole characteristics and surface integrity following abrasive waterjet drilling of Ti6Al4V/CFRP hybrid stacks
- (2019) Maojun Li et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Recent advances in drilling of carbon fiber–reinforced polymers for aerospace applications: a review
- (2019) Muhammad Aamir et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Fiber-Reinforced Polymer Composites: Manufacturing, Properties, and Applications
- (2019) Dipen Kumar Rajak et al. Polymers
- Investigation on delamination and flexural properties in drilling of carbon nanotube/polymer composites
- (2018) Hossein Heidary et al. COMPOSITE STRUCTURES
- Optimization of size and form characteristics using multi-objective grey analysis in abrasive water jet drilling of Inconel 617
- (2018) Anish Nair et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- An investigation of the hole machining processes on woven carbon-fiber reinforced polymers (CFRPs) using abrasive waterjets
- (2018) Kunlapat Thongkaew et al. MACHINING SCIENCE AND TECHNOLOGY
- Effect of Thermally Reduced Graphene Oxide on Mechanical Properties of Woven Carbon Fiber/Epoxy Composite
- (2018) Nitai Adak et al. Crystals
- Abrasive water jet drilling of advanced sustainable bio-fibre-reinforced polymer/hybrid composites: a comprehensive analysis of machining-induced damage responses
- (2018) Hom Nath Dhakal et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Experimental study on hole quality and its impact on tensile behavior following pure and abrasive waterjet cutting of plain woven CFRP laminates
- (2018) Maojun Li et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Study on carbon epoxy composite surfaces machined by abrasive water jet machining
- (2018) Ajit Dhanawade et al. JOURNAL OF COMPOSITE MATERIALS
- Prediction of surface roughness in abrasive water jet machining of CFRP composites using regression analysis
- (2017) S. Thirumalai Kumaran et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Experimental study of delamination and kerf geometry of carbon epoxy composite machined by abrasive water jet
- (2017) Ajit Dhanawade et al. JOURNAL OF COMPOSITE MATERIALS
- Experimental investigation and optimization of abrasive water jet cutting parameters for the improvement of cut quality in carbon fiber reinforced plastic laminates
- (2017) B Jagadeesh et al. Journal of Industrial Textiles
- Abrasive water jet machining of fiber-reinforced composite materials
- (2017) S Vigneshwaran et al. JOURNAL OF REINFORCED PLASTICS AND COMPOSITES
- Kerf taper and delamination damage minimization of FRP hybrid composites under abrasive water-jet machining
- (2016) Irina Wong MM et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Particles impact characteristics on cutting surface during the abrasive water jet machining: Numerical study
- (2016) Dewan Hasan Ahmed et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- An approach towards damage free machining of CFRP and GFRP composite material: a review
- (2014) Dhiraj Kumar et al. ADVANCED COMPOSITE MATERIALS
- Machining of Carbon Fiber Reinforced Plastics/Polymers: A Literature Review
- (2014) Demeng Che et al. JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME
- Numerical optimization of hole making in GFRP composite using abrasive water jet machining process
- (2014) Hussein Mohammed Ali Ibraheem et al. JOURNAL OF THE CHINESE INSTITUTE OF ENGINEERS
- Abrasive water jet machining and mechanical behavior of banyan tree saw dust powder loaded polypropylene green composites
- (2014) Narayanappa Ramesha et al. POLYMER COMPOSITES
- An analytical method for predicting damage zone in orthogonal machining of unidirectional composites
- (2013) A Sahraie Jahromi et al. JOURNAL OF COMPOSITE MATERIALS
- Graphene-based polymer nanocomposites
- (2010) Jeffrey R. Potts et al. POLYMER
- A study of abrasive water jet machining process on glass/epoxy composite laminate
- (2009) M.A. Azmir et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
- (2007) M.A. Azmir et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
Create your own webinar
Interested in hosting your own webinar? Check the schedule and propose your idea to the Peeref Content Team.
Create NowBecome a Peeref-certified reviewer
The Peeref Institute provides free reviewer training that teaches the core competencies of the academic peer review process.
Get Started