Evaluation of hole quality to explore the influence of graphene nanoplatelets embedded in epoxy/carbon composite during abrasive water jet drilling
出版年份 2022 全文链接
标题
Evaluation of hole quality to explore the influence of graphene nanoplatelets embedded in epoxy/carbon composite during abrasive water jet drilling
作者
关键词
-
出版物
Journal of Manufacturing Processes
Volume 85, Issue -, Pages 569-583
出版商
Elsevier BV
发表日期
2022-12-08
DOI
10.1016/j.jmapro.2022.11.054
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- Influence of fillers on polymeric composite during conventional machining processes: a review
- (2021) R. K. Thakur et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Study on delamination factor and surface roughness in abrasive water jet drilling of carbon fiber-reinforced polymer composites with different fiber orientation angles
- (2021) Meltem Altin Karataş et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Experimental investigation and optimization of abrasive waterjet machining parameters for GFRP composites using metaphor-less algorithms
- (2021) Dharmagna R. Tripathi et al. MATERIALS AND MANUFACTURING PROCESSES
- Impact of nanoclay filler reinforcement on CFRP composite performance during abrasive water jet machining
- (2021) R. K. Thakur et al. MATERIALS AND MANUFACTURING PROCESSES
- Experimental analysis on carbon nanotube embedded GFRP composites during AWJM
- (2021) Kalyan Kumar Singh et al. MATERIALS AND MANUFACTURING PROCESSES
- Damage study of fiber-reinforced composites drilled by abrasive waterjet —challenges and opportunities
- (2021) Yifei Zhang et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Optimization of machining parameters for kerf angle and roundness error in abrasive water jet drilling of CFRP composites with different fiber orientation angles
- (2020) Meltem Altin Karataş et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Abrasive waterjet machining of fiber-reinforced composites: a state-of-the-art review
- (2020) R. K. Thakur et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- The fatigue of carbon fibre reinforced plastics - A review
- (2019) Parvez Alam et al. COMPOSITES PART B-ENGINEERING
- Effect of pristine MWCNTs on the fatigue life of GFRP laminates-an experimental and statistical evaluation
- (2019) Anand Gaurav et al. COMPOSITES PART B-ENGINEERING
- Experimental study on hole characteristics and surface integrity following abrasive waterjet drilling of Ti6Al4V/CFRP hybrid stacks
- (2019) Maojun Li et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Recent advances in drilling of carbon fiber–reinforced polymers for aerospace applications: a review
- (2019) Muhammad Aamir et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Fiber-Reinforced Polymer Composites: Manufacturing, Properties, and Applications
- (2019) Dipen Kumar Rajak et al. Polymers
- Investigation on delamination and flexural properties in drilling of carbon nanotube/polymer composites
- (2018) Hossein Heidary et al. COMPOSITE STRUCTURES
- Optimization of size and form characteristics using multi-objective grey analysis in abrasive water jet drilling of Inconel 617
- (2018) Anish Nair et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- An investigation of the hole machining processes on woven carbon-fiber reinforced polymers (CFRPs) using abrasive waterjets
- (2018) Kunlapat Thongkaew et al. MACHINING SCIENCE AND TECHNOLOGY
- Effect of Thermally Reduced Graphene Oxide on Mechanical Properties of Woven Carbon Fiber/Epoxy Composite
- (2018) Nitai Adak et al. Crystals
- Abrasive water jet drilling of advanced sustainable bio-fibre-reinforced polymer/hybrid composites: a comprehensive analysis of machining-induced damage responses
- (2018) Hom Nath Dhakal et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Experimental study on hole quality and its impact on tensile behavior following pure and abrasive waterjet cutting of plain woven CFRP laminates
- (2018) Maojun Li et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Study on carbon epoxy composite surfaces machined by abrasive water jet machining
- (2018) Ajit Dhanawade et al. JOURNAL OF COMPOSITE MATERIALS
- Prediction of surface roughness in abrasive water jet machining of CFRP composites using regression analysis
- (2017) S. Thirumalai Kumaran et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Experimental study of delamination and kerf geometry of carbon epoxy composite machined by abrasive water jet
- (2017) Ajit Dhanawade et al. JOURNAL OF COMPOSITE MATERIALS
- Experimental investigation and optimization of abrasive water jet cutting parameters for the improvement of cut quality in carbon fiber reinforced plastic laminates
- (2017) B Jagadeesh et al. Journal of Industrial Textiles
- Abrasive water jet machining of fiber-reinforced composite materials
- (2017) S Vigneshwaran et al. JOURNAL OF REINFORCED PLASTICS AND COMPOSITES
- Kerf taper and delamination damage minimization of FRP hybrid composites under abrasive water-jet machining
- (2016) Irina Wong MM et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Particles impact characteristics on cutting surface during the abrasive water jet machining: Numerical study
- (2016) Dewan Hasan Ahmed et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- An approach towards damage free machining of CFRP and GFRP composite material: a review
- (2014) Dhiraj Kumar et al. ADVANCED COMPOSITE MATERIALS
- Machining of Carbon Fiber Reinforced Plastics/Polymers: A Literature Review
- (2014) Demeng Che et al. JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME
- Numerical optimization of hole making in GFRP composite using abrasive water jet machining process
- (2014) Hussein Mohammed Ali Ibraheem et al. JOURNAL OF THE CHINESE INSTITUTE OF ENGINEERS
- Abrasive water jet machining and mechanical behavior of banyan tree saw dust powder loaded polypropylene green composites
- (2014) Narayanappa Ramesha et al. POLYMER COMPOSITES
- An analytical method for predicting damage zone in orthogonal machining of unidirectional composites
- (2013) A Sahraie Jahromi et al. JOURNAL OF COMPOSITE MATERIALS
- Graphene-based polymer nanocomposites
- (2010) Jeffrey R. Potts et al. POLYMER
- A study of abrasive water jet machining process on glass/epoxy composite laminate
- (2009) M.A. Azmir et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
- (2007) M.A. Azmir et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
Discover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversationBecome a Peeref-certified reviewer
The Peeref Institute provides free reviewer training that teaches the core competencies of the academic peer review process.
Get Started