Environmental, technological and economical aspects of cryogenic assisted hard machining operation of inconel 718: A step towards green manufacturing

Characteristics, High Temperature Wear and Oxidation Behavior of Boride Layer Grown on Nimonic 80A Ni-based Superalloy

(2021) Ali Günen et al.   SURFACE & COATINGS TECHNOLOGY

Drilling of CFRP-Ti6Al4V stacks using CO2-cryogenic cooling

(2021) A. Rodríguez et al.   Journal of Manufacturing Processes

Investigation of mechanical and thermal loads in pcBN tooling during machining of Inconel 718

(2020) Mathias Agmell et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Influence of CO2-snow and subzero MQL on thermal aspects in the machining of Ti-6Al-4V

(2020) Muhammad Jamil et al.   APPLIED THERMAL ENGINEERING

Sustainability-based performance evaluation of hybrid nanofluid assisted machining

(2020) Aqib Mashood Khan et al.   JOURNAL OF CLEANER PRODUCTION

Performance analysis of coated carbide tool in turning of Nimonic 80A superalloy under different cutting environments

(2020) Mustafa Günay et al.   Journal of Manufacturing Processes

CO2 cryogenic milling of Inconel 718: cutting forces and tool wear

(2020) Octavio Pereira et al.   Journal of Materials Research and Technology-JMR&T

Numerical and experimental investigation of cutting forces in turning of Nimonic 80A superalloy

(2020) Mehmet Erdi Korkmaz et al.   Engineering Science and Technology-An International Journal-JESTECH

Evaluation of an environment-friendly turning process of Inconel 601 in dry conditions

(2020) Djordje Vukelic et al.   JOURNAL OF CLEANER PRODUCTION

Novel application of ultra-soft and lubricious materials for cutting tool protection and enhancement of machining induced surface integrity of Inconel 718

(2020) Saharnaz Montazeri et al.   Journal of Manufacturing Processes

Comprehensive analysis of tool wear, tool life, surface roughness, costing and carbon emissions in turning Ti–6Al–4V titanium alloy: Cryogenic versus wet machining

(2020) Chetan Agrawal et al.   TRIBOLOGY INTERNATIONAL

Environment and economic burden of sustainable cooling/lubrication methods in machining of Inconel-800

(2020) Munish Kumar Gupta et al.   JOURNAL OF CLEANER PRODUCTION

Environmentally sustainable cooling strategies in milling of SA516: Effects on surface integrity of dry, flood and MQL machining

(2020) Adam Race et al.   JOURNAL OF CLEANER PRODUCTION

Experimental investigation of cooling behavior and residual stresses for quenching with vegetable oils at different bath temperatures

(2019) Pedro Brito et al.   JOURNAL OF CLEANER PRODUCTION

Effects of hybrid Al2O3-CNT nanofluids and cryogenic cooling on machining of Ti–6Al–4V

(2019) Muhammad Jamil et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Ecological trends in machining as a key factor in sustainable production – A review

(2019) G.M. Krolczyk et al.   JOURNAL OF CLEANER PRODUCTION

Comparison between sustainable cryogenic techniques and nano-MQL cooling mode in turning of nickel-based alloy

(2019) Chetan et al.   JOURNAL OF CLEANER PRODUCTION

Selection of an ideal MQL-assisted milling condition: an NSGA-II-coupled TOPSIS approach for improving machinability of Inconel 690

(2019) Binayak Sen et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

A mechanics based prediction model for tool wear and power consumption in drilling operations and its applications

(2019) Qi Wang et al.   JOURNAL OF CLEANER PRODUCTION

Sustainable machining: an experimental investigation and optimization of machining Inconel 825 with dry and MQL approach

(2018) S. K. Tamang et al.   Journal of the Brazilian Society of Mechanical Sciences and Engineering

Hard machining performance of indigenously developed green cutting fluid using flood cooling and minimum quantity cutting fluid

(2018) Kishor Kumar Gajrani et al.   JOURNAL OF CLEANER PRODUCTION

Parameter optimization during minimum quantity lubrication milling of TC4 alloy with graphene-dispersed vegetable-oil-based cutting fluid

(2018) Ming Li et al.   JOURNAL OF CLEANER PRODUCTION

Surface integrity and sustainability assessment in high-speed machining of Inconel 718 – An eco-friendly green approach

(2017) Ganesh S. Kadam et al.   JOURNAL OF CLEANER PRODUCTION

Sustainability analysis of lubricant oils for minimum quantity lubrication based on their tribo-rheological performance

(2017) O. Pereira et al.   JOURNAL OF CLEANER PRODUCTION

Enhanced Surface Integrity From Cryogenic Machining of AZ31B Mg Alloy: A Physics-Based Analysis With Microstructure Prediction

(2017) Ninggang Shen et al.   JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME

Nozzle design for combined use of MQL and cryogenic gas in machining

(2017) Octavio Pereira et al.   International Journal of Precision Engineering and Manufacturing-Green Technology

Cryogenic and minimum quantity lubrication for an eco-efficiency turning of AISI 304

(2016) O. Pereira et al.   JOURNAL OF CLEANER PRODUCTION

Prediction of surface roughness in hard turning under high pressure coolant using Artificial Neural Network

(2016) Mozammel Mia et al.   MEASUREMENT

Evaluation of minimum quantity lubrication effects by cutting force signals in face milling of Inconel 182 overlays

(2015) Chengdong Wang et al.   JOURNAL OF CLEANER PRODUCTION

Sustainable machining of high temperature Nickel alloy – Inconel 718: part 1 – predictive performance models

(2014) Franci Pusavec et al.   JOURNAL OF CLEANER PRODUCTION

Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions

(2012) S. Zhang et al.   JOURNAL OF CLEANER PRODUCTION

Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718

(2009) Abhay Bhatt et al.   TRIBOLOGY INTERNATIONAL

Improving tool life using cryogenic cooling

(2007) Ahsan Ali Khan et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY