Effect of Substrate Alloy Type on the Microstructure of the Substrate and Deposited Material Interface in Aluminium Wire + Arc Additive Manufacturing

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

(2020) Maximilian Gierth et al.   Materials

Influence of deposition strategy of structural interface on microstructures and mechanical properties of additively manufactured Al alloy

(2020) Jianglong Gu et al.   Additive Manufacturing

An innovative process combination of additive manufacturing and sheet bulk metal forming for manufacturing a functional hybrid part

(2020) Marion Merklein et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Characterization of wear properties of the functionally graded material deposited on cast iron by laser-aided additive manufacturing

(2019) Yongfeng Liu et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Effect of compositional changes on microstructure in additively manufactured aluminum alloy 2139

(2018) Craig A. Brice et al.   MATERIALS CHARACTERIZATION

The influence of build parameters and wire batch on porosity of wire and arc additive manufactured aluminium alloy 2319

(2018) E.M. Ryan et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Design for Wire + Arc Additive Manufacture: design rules and build orientation selection

(2017) Helen Lockett et al.   JOURNAL OF ENGINEERING DESIGN

A Comparative Study of Additively Manufactured Thin Wall and Block Structure with Al-6.3%Cu Alloy Using Cold Metal Transfer Process

(2017) Baoqiang Cong et al.   Applied Sciences-Basel

The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys

(2016) Jianglong Gu et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy

(2016) Jianglong Gu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Wire + Arc Additive Manufacturing

(2016) S. W. Williams et al.   MATERIALS SCIENCE AND TECHNOLOGY

Crack path selection at the interface of wrought and wire+arc additive manufactured Ti–6Al–4V

(2016) Jikui Zhang et al.   MATERIALS & DESIGN

Mechanical properties of 2219-Al components produced by additive manufacturing with TIG

(2015) J. Y. Bai et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Precipitation behavior of aluminum alloy 2139 fabricated using additive manufacturing

(2015) Craig Brice et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

EBSD analysis of high strain rate application Al–Cu based alloys

(2015) T. Kozmel et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of temperature cycles on the microstructures and mechanical properties of the partially melted zone in the fusion welded joints of 2219 aluminum alloy

(2015) Quan Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy

(2014) Baoqiang Cong et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Control of weld composition when arc welding high strength aluminium alloys using multiple filler wires

(2010) C. G. Pickin et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

Aluminum-Copper-Lithium Alloy 2050 Developed for Medium to Thick Plate

(2009) Ph. Lequeu et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Control of weld composition when welding high strength aluminium alloy using the tandem process

(2009) C. G. Pickin et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING