Effect of electrolytic plasma polishing on microstructural evolution and tensile properties of 316L stainless steel

Test on residual stress distribution of welded S600E high-strength stainless steel sections

(2020) Baofeng Zheng et al.   JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH

Evolution of microstructure and texture of a near α titanium alloy during forging bar into disk

(2020) Guoming Zheng et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Grain refinement technology for duplex stainless steel using rapid cooling immediately before hot working

(2020) Shunsuke Sasaki et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Elucidating the grain-orientation dependent corrosion rates of austenitic stainless steels

(2020) Shiqi Dong et al.   MATERIALS & DESIGN

Effect of grain ultra-refinement on corrosion behavior of ultra-high strength high nitrogen stainless steel

(2020) H. Zhang et al.   CORROSION SCIENCE

XRD and EBSD studies of severe shot peening induced martensite transformation and grain refinements in austenitic stainless steel

(2020) Hongfei Liu et al.   MATERIALS CHARACTERIZATION

Effect of local treatment temperature of ultrasonic nanocrystalline surface modification on tribological behavior and corrosion resistance of stainless steel 316L produced by selective laser melting

(2020) Auezhan Amanov   SURFACE & COATINGS TECHNOLOGY

Machine learning based fatigue life prediction with effects of additive manufacturing process parameters for printed SS 316L

(2020) Zhixin Zhan et al.   INTERNATIONAL JOURNAL OF FATIGUE

Effectiveness of using low-temperature coolants in machining to enhance durability of AISI 316L stainless steel for reusable biomedical devices

(2019) S. Bruschi et al.   Journal of Manufacturing Processes

Process Understanding of Plasma Electrolytic Polishing through Multiphysics Simulation and Inline Metrology

(2019) Igor Danilov et al.   Micromachines

The strain-rate dependence of the Hall-Petch effect in two austenitic stainless steels with different stacking fault energies

(2019) Sergey V. Astafurov et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Fretting wear mechanism for harmonic, non-harmonic and conventional 316L stainless steels

(2019) Prabhat K. Rai et al.   WEAR

Charge transfer mechanisms underlying Contact Glow Discharge Electrolysis

(2019) Aleksey Yerokhin et al.   ELECTROCHIMICA ACTA

The effect of grain size and initial texture on microstructure, texture, and formability of Nb stabilized ferritic stainless steel manufactured by two-step cold rolling

(2019) Daniella Gomes Rodrigues et al.   Journal of Materials Research and Technology-JMR&T

Microstructural evolution and strengthening of selective laser melted 316L stainless steel processed by high-pressure torsion

(2019) Shahir Mohd Yusuf et al.   MATERIALS CHARACTERIZATION

Surface finish and properties enhancement of selective laser melted 316L stainless steel by surface mechanical attrition treatment

(2019) Y. Sun et al.   SURFACE & COATINGS TECHNOLOGY

Exceptionally high strength and good ductility in an ultrafine-grained 316L steel processed by severe plastic deformation and subsequent annealing

(2018) Moustafa El-Tahawy et al.   MATERIALS LETTERS

Deformation behaviors and cyclic strength assessment of AZ31B magnesium alloy based on steady ratcheting effect

(2018) Zhifeng Yan et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Comparative study of the effects of surface mechanical attrition treatment and conventional shot peening on low cycle fatigue of a 316L stainless steel

(2018) J. Zhou et al.   SURFACE & COATINGS TECHNOLOGY

Enhanced tensile properties of 316L stainless steel processed by a novel ultrasonic resonance plastic deformation technique

(2018) Shuaizhuo Wang et al.   MATERIALS LETTERS

Effect of texture on anisotropy at 600 °C in a near-α titanium alloy Ti60 plate

(2017) Wenyuan Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Hot pack rolling nearly lamellar Ti-44Al-8Nb-(W, B, Y) alloy with different rolling reductions: Lamellar colonies evolution and tensile properties

(2017) Haitao Zhou et al.   MATERIALS & DESIGN

Electric field effect on surface layer removal during electrolytic plasma polishing

(2016) E.V. Parfenov et al.   SURFACE & COATINGS TECHNOLOGY

Towards smart electrolytic plasma technologies: An overview of methodological approaches to process modelling

(2015) E.V. Parfenov et al.   SURFACE & COATINGS TECHNOLOGY

Deuterium transport and isotope effects in type 316L stainless steel at high temperatures for nuclear fusion and nuclear hydrogen technology applications

(2014) S.K. Lee et al.   CURRENT APPLIED PHYSICS

The effect of grain size and martensitic transformation on the wear behavior of AISI 304L stainless steel

(2014) R. Nafar Dehsorkhi et al.   MATERIALS & DESIGN

Optimizing strength and ductility of austenitic stainless steels through equal-channel angular pressing and adding nitrogen element

(2013) F.Y. Dong et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Enhanced fatigue properties of nanostructured austenitic SUS 316L stainless steel

(2011) H. Ueno et al.   ACTA MATERIALIA

Grain refinement mechanism of multiple laser shock processing impacts on ANSI 304 stainless steel

(2010) J.Z. Lu et al.   ACTA MATERIALIA

Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD

(2010) Marion Calcagnotto et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructural evolution and nanostructure formation in copper during dynamic plastic deformation at cryogenic temperatures

(2007) Y.S. Li et al.   ACTA MATERIALIA

Tensile and compressive properties of AISI 304L stainless steel subjected to equal channel angular pressing

(2007) S. Qu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING