Scalable 3D printing method for the manufacture of single-material fluidic devices with integrated filter for point of collection colourimetric analysis

Three-Dimensional Printing of Abrasive, Hard, and Thermally Conductive Synthetic Microdiamond–Polymer Composite Using Low-Cost Fused Deposition Modeling Printer

(2019) Sidra Waheed et al.   ACS Applied Materials & Interfaces

A Low-Cost Passive Sampling Device with Integrated Porous Membrane Produced using Multi-Material 3D Printing

(2018) Umme Kalsoom et al.   ANALYTICAL CHEMISTRY

Multimaterial 3D Printed Fluidic Device for Measuring Pharmaceuticals in Biological Fluids

(2018) Feng Li et al.   ANALYTICAL CHEMISTRY

Portable and selective colorimetric film and digital image colorimetry for detection of iron

(2018) Aree Choodum et al.   SPECTROCHIMICA ACTA PART A-MOLECULAR AND BIOMOLECULAR SPECTROSCOPY

Multisyringe flow injection analysis (MSFIA) for the automatic determination of total iron in wines

(2018) Piyawan Phansi et al.   FOOD CHEMISTRY

Custom 3D printer and resin for 18 μm × 20 μm microfluidic flow channels

(2017) Hua Gong et al.   LAB ON A CHIP

3D printed device including disk-based solid-phase extraction for the automated speciation of iron using the multisyringe flow injection analysis technique

(2017) Carlos Calderilla et al.   TALANTA

Nanoporous Membranes for Microfluidic Concentration Prior to Electrophoretic Separation of Proteins in Urine

(2016) Feng Li et al.   ANALYTICAL CHEMISTRY

3D-printed microfluidic devices: fabrication, advantages and limitations—a mini review

(2016) Chengpeng Chen et al.   Analytical Methods

3D-Printed Microfluidics

(2016) Anthony K. Au et al.   ANGEWANDTE CHEMIE-INTERNATIONAL EDITION

3D printed microfluidic devices: enablers and barriers

(2016) Sidra Waheed et al.   LAB ON A CHIP

The upcoming 3D-printing revolution in microfluidics

(2016) Nirveek Bhattacharjee et al.   LAB ON A CHIP

3D printing: an emerging tool for novel microfluidics and lab-on-a-chip applications

(2016) Alireza Ahmadian Yazdi et al.   Microfluidics and Nanofluidics

Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation

(2016) Ryosuke Matsuzaki et al.   Scientific Reports

3D printed microfluidics for biological applications

(2015) Chee Meng Benjamin Ho et al.   LAB ON A CHIP

Development of a portable setup and a multicommuted flow analysis procedure for the photometric determination of Fe(III) and Fe(II) in fresh water

(2015) Jeová C. Miranda et al.   SENSORS AND ACTUATORS B-CHEMICAL

Cost-Effective Three-Dimensional Printing of Visibly Transparent Microchips within Minutes

(2014) Aliaa I. Shallan et al.   ANALYTICAL CHEMISTRY

Fundamental Studies of Nanofluidics: Nanopores, Nanochannels, and Nanopipets

(2014) Daniel G. Haywood et al.   ANALYTICAL CHEMISTRY

Evaluation of 3D Printing and Its Potential Impact on Biotechnology and the Chemical Sciences

(2014) Bethany C. Gross et al.   ANALYTICAL CHEMISTRY

Bacterial siderophores efficiently provide iron to iron-starved tomato plants in hydroponics culture

(2013) W. Radzki et al.   ANTONIE VAN LEEUWENHOEK INTERNATIONAL JOURNAL OF GENERAL AND MOLECULAR MICROBIOLOGY

Lab-on-Paper with Dual Electrochemical/Colorimetric Detection for Simultaneous Determination of Gold and Iron

(2010) Amara Apilux et al.   ANALYTICAL CHEMISTRY

Separation, preconcentration and inductively coupled plasma-mass spectrometric (ICP-MS) determination of thorium(IV), titanium(IV), iron(III), lead(II) and chromium(III) on 2-nitroso-1-naphthol impregnated MCI GEL CHP20P resin

(2009) Funda Armagan Aydin et al.   JOURNAL OF HAZARDOUS MATERIALS

Self-Sealed Vertical Polymeric Nanoporous-Junctions for High-Throughput Nanofluidic Applications

(2008) Sung Jae Kim et al.   ANALYTICAL CHEMISTRY