Non-destructive quality control methods in additive manufacturing: a survey

In-situ characterization of 3D printed continuous fiber reinforced composites: A methodological study using fiber Bragg grating sensors

(2019) Charoula Kousiatza et al.   COMPOSITES SCIENCE AND TECHNOLOGY

Profile monitoring based quality control method for fused deposition modeling process

(2018) Ketai He et al.   JOURNAL OF INTELLIGENT MANUFACTURING

A feasibility study on process monitoring and control in vat photopolymerization of ceramics

(2018) Thomas Hafkamp et al.   MECHATRONICS

Quality control issues in 3D-printing manufacturing: a review

(2018) Hsin-Chieh Wu et al.   RAPID PROTOTYPING JOURNAL

Investigation of new volumetric non-destructive techniques to characterise additive manufacturing parts

(2018) A-F. Obaton et al.   Welding in the World

In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing

(2018) Chu Lun Alex Leung et al.   Nature Communications

In-Plane Shape-Deviation Modeling and Compensation for Fused Deposition Modeling Processes

(2017) Andi Wang et al.   IEEE Transactions on Automation Science and Engineering

Influence of irradiation parameters on the polymerization of ceramic reactive suspensions for stereolithography

(2017) Thierry Chartier et al.   JOURNAL OF THE EUROPEAN CERAMIC SOCIETY

Process defects andin situmonitoring methods in metal powder bed fusion: a review

(2017) Marco Grasso et al.   MEASUREMENT SCIENCE and TECHNOLOGY

A dynamic model for nozzle clog monitoring in fused deposition modelling

(2017) Yedige Tlegenov et al.   RAPID PROTOTYPING JOURNAL

Impact of the Fused Deposition (FDM) Printing Process on Polylactic Acid (PLA) Chemistry and Structure

(2017) Michael Arthur Cuiffo et al.   Applied Sciences-Basel

A review on measurement science needs for real-time control of additive manufacturing metal powder bed fusion processes

(2016) Mahesh Mani et al.   INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH

Spatially dependent properties in a laser additive manufactured Ti–6Al–4V component

(2016) S. Palanivel et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Simulation study on evolutionary cycle to cycle time control of exposure controlled projection lithography

(2016) Xiayun Zhao et al.   RAPID PROTOTYPING JOURNAL

Invited Review Article: Review of post-process optical form metrology for industrial-grade metal additive manufactured parts

(2016) P. I. Stavroulakis et al.   REVIEW OF SCIENTIFIC INSTRUMENTS

A comparative study of additive manufacturing techniques: Residual stress and microstructural analysis of CLAD and WAAM printed Ti–6Al–4V components

(2016) Blanka A. Szost et al.   MATERIALS & DESIGN

Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing

(2016) Sarah K. Everton et al.   MATERIALS & DESIGN

Quality Investigation of 3D Printer Filament Using Laboratory X-Ray Tomography

(2016) Anton du Plessis et al.   3D Printing and Additive Manufacturing

Directionality of Cavities and Porosity Formation in Powder-Bed Laser Additive Manufacturing of Metal Components Investigated Using X-Ray Tomography

(2016) Anton du Plessis et al.   3D Printing and Additive Manufacturing

In situ monitoring and characterization of distortion during laser cladding of Inconel® 625

(2015) J.C. Heigel et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Effect of inter-layer dwell time on distortion and residual stress in additive manufacturing of titanium and nickel alloys

(2015) Erik R. Denlinger et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Optimal offline compensation of shape shrinkage for three-dimensional printing processes

(2014) Qiang Huang et al.   IIE TRANSACTIONS

Vision-based defect detection in laser metal deposition process

(2014) Shyam Barua et al.   RAPID PROTOTYPING JOURNAL

Characterization of Metal Powders Used for Additive Manufacturing

(2014) J. A. Slotwinski et al.   JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY

Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control

(2014) John A. Slotwinski et al.   JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY

Investigation of laser consolidation process for metal powder by two-color pyrometer and high-speed video camera

(2013) Tatsuaki Furumoto et al.   CIRP ANNALS-MANUFACTURING TECHNOLOGY

Residual Stress and Deformation of Consolidated Structure Obtained by Layered Manufacturing Process

(2013) Mohd Sanusi ABDUL AZIZ et al.   Journal of Advanced Mechanical Design Systems and Manufacturing

Accuracy of medical models made by additive manufacturing (rapid manufacturing)

(2013) Mika Salmi et al.   JOURNAL OF CRANIO-MAXILLOFACIAL SURGERY

Parametric study on a coaxial multi-material powder flow in laser-based powder deposition process

(2012) Prabu Balu et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Study on influential factors for process monitoring and control in laser aided additive manufacturing

(2012) G. Bi et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

In situ flaw detection by IR‐imaging during electron beam melting

(2012) Jan Schwerdtfeger et al.   RAPID PROTOTYPING JOURNAL

Determination of geometrical factors in Layerwise Laser Melting using optical process monitoring

(2011) Tom Craeghs et al.   OPTICS AND LASERS IN ENGINEERING

Development of low‐cost imaging system for laser metal deposition processes

(2011) Shyam Barua et al.   RAPID PROTOTYPING JOURNAL

Comparison of density measurement techniques for additive manufactured metallic parts

(2011) A.B. Spierings et al.   RAPID PROTOTYPING JOURNAL

The investigation of the influence of laser re‐melting on density, surface quality and microstructure of selective laser melting parts

(2011) Evren Yasa et al.   RAPID PROTOTYPING JOURNAL

Influence of the particle size distribution on surface quality and mechanical properties in AM steel parts

(2011) A.B. Spierings et al.   RAPID PROTOTYPING JOURNAL

Improving dimensional accuracy of Fused Deposition Modelling processed part using grey Taguchi method

(2009) Anoop Kumar Sood et al.   MATERIALS & DESIGN

Effect of processing conditions on the bonding quality of FDM polymer filaments

(2008) Q. Sun et al.   RAPID PROTOTYPING JOURNAL