标题
Non-destructive quality control methods in additive manufacturing: a survey
作者
关键词
-
出版物
RAPID PROTOTYPING JOURNAL
Volume 26, Issue 4, Pages 777-790
出版商
Emerald
发表日期
2020-03-17
DOI
10.1108/rpj-08-2019-0224
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- In-situ characterization of 3D printed continuous fiber reinforced composites: A methodological study using fiber Bragg grating sensors
- (2019) Charoula Kousiatza et al. COMPOSITES SCIENCE AND TECHNOLOGY
- Profile monitoring based quality control method for fused deposition modeling process
- (2018) Ketai He et al. JOURNAL OF INTELLIGENT MANUFACTURING
- A feasibility study on process monitoring and control in vat photopolymerization of ceramics
- (2018) Thomas Hafkamp et al. MECHATRONICS
- Quality control issues in 3D-printing manufacturing: a review
- (2018) Hsin-Chieh Wu et al. RAPID PROTOTYPING JOURNAL
- Investigation of new volumetric non-destructive techniques to characterise additive manufacturing parts
- (2018) A-F. Obaton et al. Welding in the World
- In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing
- (2018) Chu Lun Alex Leung et al. Nature Communications
- In-Plane Shape-Deviation Modeling and Compensation for Fused Deposition Modeling Processes
- (2017) Andi Wang et al. IEEE Transactions on Automation Science and Engineering
- Influence of irradiation parameters on the polymerization of ceramic reactive suspensions for stereolithography
- (2017) Thierry Chartier et al. JOURNAL OF THE EUROPEAN CERAMIC SOCIETY
- Process defects andin situmonitoring methods in metal powder bed fusion: a review
- (2017) Marco Grasso et al. MEASUREMENT SCIENCE and TECHNOLOGY
- A dynamic model for nozzle clog monitoring in fused deposition modelling
- (2017) Yedige Tlegenov et al. RAPID PROTOTYPING JOURNAL
- Impact of the Fused Deposition (FDM) Printing Process on Polylactic Acid (PLA) Chemistry and Structure
- (2017) Michael Arthur Cuiffo et al. Applied Sciences-Basel
- A review on measurement science needs for real-time control of additive manufacturing metal powder bed fusion processes
- (2016) Mahesh Mani et al. INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH
- Spatially dependent properties in a laser additive manufactured Ti–6Al–4V component
- (2016) S. Palanivel et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Simulation study on evolutionary cycle to cycle time control of exposure controlled projection lithography
- (2016) Xiayun Zhao et al. RAPID PROTOTYPING JOURNAL
- Invited Review Article: Review of post-process optical form metrology for industrial-grade metal additive manufactured parts
- (2016) P. I. Stavroulakis et al. REVIEW OF SCIENTIFIC INSTRUMENTS
- A comparative study of additive manufacturing techniques: Residual stress and microstructural analysis of CLAD and WAAM printed Ti–6Al–4V components
- (2016) Blanka A. Szost et al. MATERIALS & DESIGN
- Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
- (2016) Sarah K. Everton et al. MATERIALS & DESIGN
- Quality Investigation of 3D Printer Filament Using Laboratory X-Ray Tomography
- (2016) Anton du Plessis et al. 3D Printing and Additive Manufacturing
- Directionality of Cavities and Porosity Formation in Powder-Bed Laser Additive Manufacturing of Metal Components Investigated Using X-Ray Tomography
- (2016) Anton du Plessis et al. 3D Printing and Additive Manufacturing
- In situ monitoring and characterization of distortion during laser cladding of Inconel® 625
- (2015) J.C. Heigel et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Effect of inter-layer dwell time on distortion and residual stress in additive manufacturing of titanium and nickel alloys
- (2015) Erik R. Denlinger et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Optimal offline compensation of shape shrinkage for three-dimensional printing processes
- (2014) Qiang Huang et al. IIE TRANSACTIONS
- Vision-based defect detection in laser metal deposition process
- (2014) Shyam Barua et al. RAPID PROTOTYPING JOURNAL
- Characterization of Metal Powders Used for Additive Manufacturing
- (2014) J. A. Slotwinski et al. JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY
- Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control
- (2014) John A. Slotwinski et al. JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY
- Investigation of laser consolidation process for metal powder by two-color pyrometer and high-speed video camera
- (2013) Tatsuaki Furumoto et al. CIRP ANNALS-MANUFACTURING TECHNOLOGY
- Residual Stress and Deformation of Consolidated Structure Obtained by Layered Manufacturing Process
- (2013) Mohd Sanusi ABDUL AZIZ et al. Journal of Advanced Mechanical Design Systems and Manufacturing
- Accuracy of medical models made by additive manufacturing (rapid manufacturing)
- (2013) Mika Salmi et al. JOURNAL OF CRANIO-MAXILLOFACIAL SURGERY
- Parametric study on a coaxial multi-material powder flow in laser-based powder deposition process
- (2012) Prabu Balu et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Study on influential factors for process monitoring and control in laser aided additive manufacturing
- (2012) G. Bi et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- In situ flaw detection by IR‐imaging during electron beam melting
- (2012) Jan Schwerdtfeger et al. RAPID PROTOTYPING JOURNAL
- Determination of geometrical factors in Layerwise Laser Melting using optical process monitoring
- (2011) Tom Craeghs et al. OPTICS AND LASERS IN ENGINEERING
- Development of low‐cost imaging system for laser metal deposition processes
- (2011) Shyam Barua et al. RAPID PROTOTYPING JOURNAL
- Comparison of density measurement techniques for additive manufactured metallic parts
- (2011) A.B. Spierings et al. RAPID PROTOTYPING JOURNAL
- The investigation of the influence of laser re‐melting on density, surface quality and microstructure of selective laser melting parts
- (2011) Evren Yasa et al. RAPID PROTOTYPING JOURNAL
- Influence of the particle size distribution on surface quality and mechanical properties in AM steel parts
- (2011) A.B. Spierings et al. RAPID PROTOTYPING JOURNAL
- Improving dimensional accuracy of Fused Deposition Modelling processed part using grey Taguchi method
- (2009) Anoop Kumar Sood et al. MATERIALS & DESIGN
- Effect of processing conditions on the bonding quality of FDM polymer filaments
- (2008) Q. Sun et al. RAPID PROTOTYPING JOURNAL
Publish scientific posters with Peeref
Peeref publishes scientific posters from all research disciplines. Our Diamond Open Access policy means free access to content and no publication fees for authors.
Learn MoreBecome a Peeref-certified reviewer
The Peeref Institute provides free reviewer training that teaches the core competencies of the academic peer review process.
Get Started