Melt Crystallization Behavior of Injection-Molded High-Density Polyethylene Based Upon a Solidification Kinetic Analysis

Investigation on solidification behaviour of high-density polyethylene during thin-walled injection moulding: correlation between crystallisation kinetics and thermal gradient field

(2016) B. Yang et al.   PLASTICS RUBBER AND COMPOSITES

Formation of double skin-core orientated structure in injection-molded Polyethylene parts: Effects of ultra-high molecular weight Polyethylene and temperature field

(2014) Jian Feng et al.   JOURNAL OF POLYMER RESEARCH

Correlation Between Solidification Behavior and Melt Crystallization Kinetics ofIsotacticPolypropylene (iPP) during Injection Molding

(2013) Bin Yang et al.   Journal of Macromolecular Science Part B-Physics

Influence of high molecular weight component on the hierarchical crystalline structures of injection-molded bars of polyethylene

(2013) Long Wang et al.   POLYMER INTERNATIONAL

Effects of annealing on the hierarchical crystalline structures and mechanical properties of injection-molded bars of high-density polyethylene

(2013) Long Wang et al.   POLYMER INTERNATIONAL

Hierarchical crystalline structures and dynamic mechanical properties of injection-molded bars of HDPE: attributes of temperature field

(2013) Long Wang et al.   POLYMERS FOR ADVANCED TECHNOLOGIES

Water Penetration Behavior in Water-assisted Injection Molding (WAIM): A Study of Product Quality for Different Process and Material Parameters

(2012) S. Sannen et al.   INTERNATIONAL POLYMER PROCESSING

Rheological and mechanical behavior of ethyl vinyl acetate/low density polyethylene blends for injection molding

(2012) Antonio Iannaccone et al.   JOURNAL OF APPLIED POLYMER SCIENCE

Real-time diagnosing polymer processing in injection molding using ultrasound

(2012) Lijuan Zhao et al.   JOURNAL OF APPLIED POLYMER SCIENCE

Study on the solidification kinetics of high-density polyethylene during thin-walled injection molding process

(2012) Shuang-quan Deng et al.   JOURNAL OF POLYMER ENGINEERING

Crystallization behavior and molecular orientation of high density polyethylene parts prepared by gas-assisted injection molding

(2012) Nan Sun et al.   POLYMER INTERNATIONAL

Modeling of flow-induced crystallization in blends of isotactic polypropylene and poly(ethylene-co-octene)

(2012) Fengyuan Yu et al.   POLYMER INTERNATIONAL

THREE DIMENSIONAL NUMERICAL SIMULATION OF POLYMER CRYSTALLIZATION DURING PLASTIC INJECTION MOLDING

(2011) Bo YAN et al.   ACTA POLYMERICA SINICA

Mold temperature control using high-frequency proximity effect induced heating

(2011) Shia-Chung Chen et al.   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

Modeling and Analysis of Process Parameters for Evaluating Shrinkage Problems During Plastic Injection Molding of a DVD-ROM Cover

(2011) H. Öktem   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Effect of long chain branching on nonisothermal crystallization behavior of polyethylenes synthesized with constrained geometry catalyst

(2011) Bin Yang et al.   POLYMER ENGINEERING AND SCIENCE

Oriented structure in stretched isotactic polypropylene melt and its unexpected recrystallization: optical and X-ray studies

(2011) Guoqiang Zheng et al.   POLYMER INTERNATIONAL

Effect of annealing on the microstructure and mechanical properties of polypropylene with oriented shish-kebab structure

(2011) Hongwei Bai et al.   POLYMER INTERNATIONAL

Inverse estimation of the crystallization kinetic function of semi-crystalline polymers and short fibre reinforced composites in moderate cooling conditions

(2011) R. Le Goff et al.   POLYMER TESTING

A simple method for forecast of cooling time of high-density polyethylene during gas-assisted injection molding

(2010) Shui-Po Liang et al.   JOURNAL OF APPLIED POLYMER SCIENCE

Prediction of Heat Conduction with Phase-change Effects during Cooling Stage of Injection Molding of High-density Polyethylene: Approximate Integral Approach

(2010) Bin Yang et al.   Journal of Macromolecular Science Part B-Physics

In-Situ Shrinkage Sensor for Injection Molding

(2010) Rahul R. Panchal et al.   JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME

Frozen-in birefringence and anisotropic shrinkage in optical moldings: II. Comparison of simulations with experiments on light-guide plates

(2010) Avraam I. Isayev et al.   POLYMER

Study of the effect of organic clay on the shear-induced crystallization of high-density polyethylene through dynamic-packing injection molding

(2010) Cong Deng et al.   POLYMER INTERNATIONAL

Effect of Melt and Mold Temperatures on the Solidification Behavior of HDPE during Gas-Assisted Injection Molding: An Enthalpy Transformation Approach

(2009) Bin Yang et al.   MACROMOLECULAR MATERIALS AND ENGINEERING

In-situ temperature measurements in the depths of injection molded parts

(2009) Shih-Jung Liu et al.   MEASUREMENT

Simulation of phase-change heat transfer during cooling stage of gas-assisted injection molding of high-density polyethylene via enthalpy transformation approach

(2009) Bin Yang et al.   POLYMER ENGINEERING AND SCIENCE

Optimization of Residual Stresses in the Surface Regions of Injection Moldings

(2009) Mirigul Altan et al.   POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING

Heat transfer in injection molding for reproduction of sub-micron-sized features

(2008) M. Nakao et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

A simplified approach to predict part temperature and minimum “safe” cycle time

(2008) Yunior Hioe et al.   POLYMER ENGINEERING AND SCIENCE

Novel three-dimensional in-cavity transient temperature measurements in injection molding and fluid-assisted injection molding

(2008) Shih-Jung Liu et al.   POLYMER TESTING

Numerical Simulations and Verifications of Cyclic and Transient Temperature Variations in Injection Molding Process

(2008) Hai-Mei Li et al.   POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING