Realisation of a multi-sensor framework for process monitoring of the wire arc additive manufacturing in producing Ti-6Al-4V parts
Published 2018 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
Realisation of a multi-sensor framework for process monitoring of the wire arc additive manufacturing in producing Ti-6Al-4V parts
Authors
Keywords
-
Journal
INTERNATIONAL JOURNAL OF COMPUTER INTEGRATED MANUFACTURING
Volume 31, Issue 8, Pages 785-798
Publisher
Informa UK Limited
Online
2018-04-30
DOI
10.1080/0951192x.2018.1466395
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Fabrication of inclined thin-walled parts in multi-layer single-pass GMAW-based additive manufacturing with flat position deposition
- (2017) Jun Xiong et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Closed-loop control of variable layer width for thin-walled parts in wire and arc additive manufacturing
- (2016) Jun Xiong et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Wire + Arc Additive Manufacturing
- (2016) S. W. Williams et al. MATERIALS SCIENCE AND TECHNOLOGY
- X-ray computed tomography for additive manufacturing: a review
- (2016) A Thompson et al. MEASUREMENT SCIENCE and TECHNOLOGY
- Microstructural evolution and mechanical properties of Ti-6Al-4V wall deposited by pulsed plasma arc additive manufacturing
- (2016) J.J. Lin et al. MATERIALS & DESIGN
- Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing
- (2016) Sarah K. Everton et al. MATERIALS & DESIGN
- Unknown
- (2016) ADVANCED ENGINEERING MATERIALS
- Wire-feed additive manufacturing of metal components: technologies, developments and future interests
- (2015) Donghong Ding et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Development of a laminar flow local shielding device for wire + arc additive manufacture
- (2015) J. Ding et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Microstructure of Interpass Rolled Wire + Arc Additive Manufacturing Ti-6Al-4V Components
- (2015) Filomeno Martina et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- On-line monitor of hydrogen porosity based on arc spectral information in Al–Mg alloy pulsed gas tungsten arc welding
- (2015) Huanwei Yu et al. OPTICS AND LASER TECHNOLOGY
- Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy
- (2014) Baoqiang Cong et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Metal Additive Manufacturing: A Review
- (2014) William E. Frazier JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
- Development of micro-plasma transferred arc (μ-PTA) wire deposition process for additive layer manufacturing applications
- (2014) Suyog Jhavar et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control
- (2014) John A. Slotwinski et al. JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY
- Application of arc plasma spectral information in the monitor of Al–Mg alloy pulsed GTAW penetration status based on fuzzy logic system
- (2013) Huanwei Yu et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Improving prediction accuracy of thermal analysis for weld-based additive manufacturing by calibrating input parameters using IR imaging
- (2013) Xingwang Bai et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Microstructure and residual stress improvement in wire and arc additively manufactured parts through high-pressure rolling
- (2013) Paul A. Colegrove et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Advanced lattice support structures for metal additive manufacturing
- (2013) Ahmed Hussein et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Online measurement of bead geometry in GMAW-based additive manufacturing using passive vision
- (2013) Jun Xiong et al. MEASUREMENT SCIENCE and TECHNOLOGY
- Plasma arc welding: Process, sensing, control and modeling
- (2013) C.S. Wu et al. Journal of Manufacturing Processes
- Understanding the Basis of the Kalman Filter Via a Simple and Intuitive Derivation [Lecture Notes]
- (2012) Ramsey Faragher IEEE SIGNAL PROCESSING MAGAZINE
- Vision-sensing and bead width control of a single-bead multi-layer part: material and energy savings in GMAW-based rapid manufacturing
- (2012) Jun Xiong et al. JOURNAL OF CLEANER PRODUCTION
- Wire based additive layer manufacturing: Comparison of microstructure and mechanical properties of Ti–6Al–4V components fabricated by laser-beam deposition and shaped metal deposition
- (2011) Bernd Baufeld et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- A novel control algorithm for weld pool control
- (2010) Fenglin Lü et al. Industrial Robot-The International Journal of Robotics Research and Application
- A study on application of multi‐sensor information fusion in pulsed GTAW
- (2010) Bo Chen et al. Industrial Robot-The International Journal of Robotics Research and Application
- Investigation on arc sound and metal transfer modes for on-line monitoring in pulsed gas metal arc welding
- (2010) Kamal Pal et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Additive manufacturing of Ti–6Al–4V components by shaped metal deposition: Microstructure and mechanical properties
- (2009) Bernd Baufeld et al. MATERIALS & DESIGN
Find Funding. Review Successful Grants.
Explore over 25,000 new funding opportunities and over 6,000,000 successful grants.
ExploreAsk a Question. Answer a Question.
Quickly pose questions to the entire community. Debate answers and get clarity on the most important issues facing researchers.
Get Started