4.6 Article

Stark effects in D35-sensitized mesoporous TiO2: influence of dye coverage and electrolyte composition

Journal

ELECTROCHIMICA ACTA
Volume 179, Issue -, Pages 174-178

Publisher

PERGAMON-ELSEVIER SCIENCE LTD
DOI: 10.1016/j.electacta.2015.01.068

Keywords

Dye-sensitized solar cell; charge compensation; cation adsorption; Helmholtz layer

Funding

  1. European Community's Seventh Framework Programme (FP7) of the SANS project [246124]
  2. Swedish Energy Agency
  3. STandUp for Energy program

Ask authors/readers for more resources

Strong Stark effects are visible in the spectra of the organic donor-pi-acceptor dye D35 when it is adsorbed onto mesoporous TiO2, both under steady state conditions and under modulated light conditions. The addition of lithium cations to the electrolyte results in a significant red shift of the D35 absorption spectrum, which is attributed to adsorption of Li+ at the TiO2 surface, resulting in a change of the electric field across the adsorbed dye molecules. The dye molecules must therefore be located inside the Helmholtz double layer at the TiO2/electrolyte interface. In photoinduced absorption (PIA) spectroscopy, modulated light is used to excite dye molecules. A significant Stark bleach is found in PIA spectra, which corresponds to a blue shift of the dye absorption spectrum upon addition of electrons to TiO2, due to an electric field across the dye monolayer. The observed bleach is reduced when the concentration of supporting electrolyte is increased, indicating local charge compensation of the electrons in TiO2 by adsorbed cations. Transient absorption studies reveal that screening of the interfacial electric field is faster at lower dye coverage compared to full monolayer coverage. Analysis of the Stark effect in dye-sensitized solar cell gives valuable information on the mechanism of charge compensation of electrons in mesoporous electrodes. (C) 2015 Elsevier Ltd. All rights reserved.

Authors

I am an author on this paper
Click your name to claim this paper and add it to your profile.

Reviews

Primary Rating

4.6
Not enough ratings

Secondary Ratings

Novelty
-
Significance
-
Scientific rigor
-
Rate this paper

Recommended

Article Nanoscience & Nanotechnology

Oriented Crystal Growth during Perovskite Surface Reconstruction

Hyeon-Seo Choi, Yu-Na Kim, Seungyeon Hong, Bowen Yang, Jiajia Suo, Ji-Youn Seo, Seok Joon Kwon, Anders Hagfeldt, Hyo Jung Kim, Wan In Lee, Hui-Seon Kim

Summary: Surface passivation using a mixed salt has been shown to improve the performance and stability of perovskite solar cells. The length of the alkyl chain in the mixed salt can manipulate the crystal formation dynamics and enhance the (001) plane. The enhanced crystal orientation during surface recrystallization reduces trap density and suppresses charge recombination, leading to an increase in open-circuit voltage and fill factor.

ACS APPLIED MATERIALS & INTERFACES (2022)

Article Multidisciplinary Sciences

Hydroxamic acid pre-adsorption raises the efficiency of cosensitized solar cells

Yameng Ren, Dan Zhang, Jiajia Suo, Yiming Cao, Felix T. Eickemeyer, Nick Vlachopoulos, Shaik M. Zakeeruddin, Anders Hagfeldt, Michael Graetzel

Summary: We report a method of pre-adsorbing a monolayer of a hydroxamic acid derivative on the surface of titanium dioxide to improve the dye molecular packing and photovoltaic performance of two newly designed co-adsorbed sensitizers. The best performing cosensitized solar cells exhibited a power conversion efficiency of 15.2% under a standard air mass of 1.5 global simulated sunlight and showed long-term operational stability of 500 hours.

NATURE (2023)

Editorial Material Chemistry, Physical

Can Alternative Module Design Help to Overcome Stability Problems of Perovskite Photovoltaics?

Gerrit Boschloo

ACS ENERGY LETTERS (2023)

Article Electrochemistry

Reduced hysteresis and enhanced air stability of low-temperature processed carbon-based perovskite solar cells by surface modification

Soe Ko Ko Aung, Anuja Vijayan, Masoud Karimipour, Tosawat Seetawan, Gerrit Boschloo

Summary: Low temperature processed carbon-based perovskite solar cells (C-PSCs) have been developed as low-cost and easily fabricated alternatives to traditional perovskite solar cells. However, their power conversion efficiency (PCE) still lags behind that of traditional perovskite solar cells with gold contacts.

ELECTROCHIMICA ACTA (2023)

Article Chemistry, Physical

N,N-Bis(9-methyl-3-carbazolyl)-4-anisidine as an Electroactive Material for Use in Perovskite Solar Cells

Jonas Keruckas, Patryk Janasik, Rasa Keruckiene, Pawel Czulkin, Malgorzata Czichy, Mieczyslaw Lapkowski, Dmytro Volyniuk, Ranush Durgaryan, Byeong Jo Kim, Gerrit Boschloo, Juozas Vidas Grazulevicius

Summary: This study presents Di-(9-methyl-3-carbazolyl)-(4-anisyl)-amine as an effective hole-transporting material for perovskite solar cells. The compound is synthesized from inexpensive starting compounds through a three-step synthesis. It exhibits reversible double-wave electrochemical oxidation and polymerization at higher potential. The compound has been used to fabricate dopant-free hole-transporting layers in perovskite solar cells, achieving a power conversion efficiency of 15.5%.

ACS APPLIED ENERGY MATERIALS (2023)

Article Chemistry, Physical

Solvent Engineering of Perovskite Crystallization for High Band Gap FAPbBr3 Perovskite Solar Cells Prepared in Ambient Condition

Yawen Liu, Bin Cai, Hao Yang, Gerrit Boschloo, Erik M. J. Johansson

Summary: High band gap FAPbBr(3) perovskite solar cells have attracted tremendous interest recently due to their high open circuit voltage and good stability. A mixed solvent approach for the second step of preparation was introduced, which resulted in favorable properties and improved power conversion efficiency. Addition of a small amount of MACl further enhanced the photovoltage performance, achieving a high PCE of 9.23% under ambient conditions.

ACS APPLIED ENERGY MATERIALS (2023)

Editorial Material Chemistry, Physical

Joint Forum on Halide Perovskite Materials and Devices for Energy and Electronic Applications

Suchismita Guha, Gerrit Boschloo

ACS APPLIED ENERGY MATERIALS (2023)

Editorial Material Engineering, Electrical & Electronic

Joint Forum on Halide Perovskite Materials and Devices for Energy and Electronic Applications

Suchismita Guha, Gerrit Boschloo

ACS APPLIED ELECTRONIC MATERIALS (2023)

Editorial Material Chemistry, Physical

Introduction to 1D/2D materials for energy, medicine and devices

Yu Chen, Gemma-Louise Davies, Anders Hagfeldt, Nicholas Kotov

JOURNAL OF MATERIALS CHEMISTRY A (2023)

Review Chemistry, Physical

Recent progress on the use of graphene-based nanomaterials in perovskite solar cells

Zohreh Niazi, Anders Hagfeldt, Elaheh K. Goharshadi

Summary: Graphene-based nanomaterials (GBNs) have been incorporated in various components of perovskite solar cells (PSCs) to address the challenges of stability, scalability, and flexibility. These materials, with their excellent optical, electronic, photonic, thermal, and mechanical properties, have shown promise in improving the efficiency, reproducibility, and stability of PSCs.

JOURNAL OF MATERIALS CHEMISTRY A (2023)

Article Chemistry, Multidisciplinary

Amine Gas-Induced Reversible Optical Bleaching of Bismuth-Based Lead-Free Perovskite Thin Films

Fuxiang Ji, Bin Zhang, Weimin M. Chen, Irina A. Buyanova, Feng Wang, Gerrit Boschloo

Summary: Lead-free perovskites with reversible and switchable optical properties have potential applications in smart windows, sensors, data encryption, and other on-demand devices. This study demonstrates for the first time the switchable optical bleaching of bismuth-based perovskite films induced by methylamine gas, and reveals the underlying mechanism.

ADVANCED SCIENCE (2023)

Article Chemistry, Physical

Electron-hopping across dye-sensitized mesoporous NiO surfaces

Sina Wrede, Lanlan He, Gerrit Boschloo, Leif Hammarstrom, Lars Kloo, Haining Tian

Summary: To gain a deeper understanding of charge processes in dye-sensitized photocathodes, lateral electron hopping across dye-sensitized NiO photocathodes was investigated. The results show the existence of a second electron hopping pathway between NiO surface states, which dominates recombination kinetics. The study highlights the importance of fast electron transport in sensitized NiO photocathodes.

PHYSICAL CHEMISTRY CHEMICAL PHYSICS (2022)

Review Chemistry, Multidisciplinary

Strain effects on halide perovskite solar cells

Bowen Yang, Dmitry Bogachuk, Jiajia Suo, Lukas Wagner, Hobeom Kim, Jaekeun Lim, Andreas Hinsch, Gerrit Boschloo, Mohammad Khaja Nazeeruddin, Anders Hagfeldt

Summary: This article reviews the influence of strain on the performance and stability of halide perovskite solar cells, covering the origins, characterization techniques, and control strategies of strain. It also proposes effective strategies for future strain engineering. The comprehensive review is important for researchers to gain a deeper understanding of strain effects and improve performance towards commercialization.

CHEMICAL SOCIETY REVIEWS (2022)

Article Chemistry, Physical

Copper coordination polymers with selective hole conductivity

Hannes Michaels, Matthias J. Golomb, Byeong Jo Kim, Tomas Edvinsson, Fabio Cucinotta, Paul G. Waddell, Michael R. Probert, Steven J. Konezny, Gerrit Boschloo, Aron Walsh, Marina Freitag

Summary: Emerging technologies in solar energy play a critical role in addressing energy challenges and achieving carbon neutrality. Limitations in charge transport materials hinder the development of energy conversion and storage technologies. Low-dimensional coordination polymers offer a viable alternative with molecular building blocks for efficient charge transport.

JOURNAL OF MATERIALS CHEMISTRY A (2022)

Article Chemistry, Physical

The Complex Degradation Mechanism of Copper Electrodes on Lead Halide Perovskites

Sebastian Svanstrom, Alberto Garcia-Fernandez, T. Jesper Jacobsson, Ieva Bidermane, Torsten Leitner, Tamara Sloboda, Gabriel J. Man, Gerrit Boschloo, Erik M. J. Johansson, Hakan Rensmo, Ute B. Cappel

Summary: This study investigates the interface reactions between lead halide perovskites and copper in solar cells, revealing rich interfacial chemistry and significant degradation of both copper and perovskite over time in the presence of oxygen and moisture.

ACS MATERIALS AU (2022)

Article Electrochemistry

Recent advances in Bio-mass by electrochemically strategies generated hydrogen gas production: Environmentally sustainable technologies innovation

Abdul Qayoom Mugheri, Shaista Khan, Ali Asghar Sangah, Aijaz Ahmed Bhutto, Muhammad Younis Laghari, Nadeem Ahmed Mugheri, Asif Ali Jamali, Arsalan Ahmed Mugheri, Nagji Sodho, Abdul Waheed Mastoi, Aftab Kandhro

Summary: Green hydrogen has the potential to transition to a pollution-free energy infrastructure. This study proposes a solution to produce hydrogen during the photoelectrochemical process, offering greater stability and control over chemical reactions. Techno-economic assessments show the efficiency and economic feasibility of co-producing value-added chemicals to enhance green hydrogen production.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

ACGNet: An interpretable attention crystal graph neural network for accurate oxidation potential prediction

Danpeng Cheng, Wuxin Sha, Qigao Han, Shun Tang, Jun Zhong, Jinqiao Du, Jie Tian, Yuan-Cheng Cao

Summary: LiNixCoyMn1-x-yO2 (NCM) is a critical cathode material for lithium-ion batteries in electric vehicles. The aging of cathode/electrolyte interfaces leads to capacity degradation and long-term cycle instability. A novel neural network model called ACGNet is developed to predict electrochemical stability windows of crystals, allowing for high-throughput screening of coating materials. LiPO3 is identified as a promising coating material with high oxidation voltage and low cost, which significantly improves the cycle stability of NCM batteries. This study demonstrates the accuracy and potential of machine learning in battery materials.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Enhanced electrochemical performance of CuO/NiO/rGO for oxygen evolution reaction

P. Mohana, R. Yuvakkumar, G. Ravi, S. Arunmetha

Summary: This study successfully fabricates a non-noble CuO/NiO/rGO nanocomposite and investigates its electrocatalytic performance for oxygen evolution reaction in alkaline environment. The experimental results demonstrate that the electrocatalyst exhibits high activity and good stability, offering a new synthetic approach for sustainable energy production.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Carbon nanofibers implanted porous catalytic metal oxide design as efficient bifunctional electrode host material for lithium-sulfur battery

Qiong Qu, Jing Guo, Hongyu Wang, Kai Zhang, Jingde Li

Summary: In this study, a bifunctional electrode host design consisting of carbon nanofibers implanted ordered porous Co-decorated Al2O3 supported on carbon nanotube film (CNTF) was proposed to address the shuttling effect of lithium polysulfides (LiPSs) and dendrite formation of metal lithium anode in lithium-sulfur (Li-S) batteries. The electrode exhibited excellent conductivity, efficient confinement of LiPSs, and catalytic conversion performance, resulting in high initial capacity and good capacity retention during cycling. As an anode, the electrode showed excellent Li+ diffusion performance and uniform lithium growth behavior, achieving a dendrite-free lithium electrode. The flexible pack cell assembled from these electrodes delivered a specific capacity of 972 mAh g(-1) with good capacity retention.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Spray coating of carbon nanoparticles as an effective and scalable method to enhance the performance of stainless steel anode in microbial electrochemical systems

Hong Zhang, Jin-Peng Yu, Chen Chen, Cheng-Yong Shu, Guang-Yu Xu, Jie Ren, Kai Cui, Wen-Fang Cai, Yun-Hai Wang, Kun Guo

Summary: Spray coating of acetylene black nanoparticles onto stainless steel mesh can enhance its biofilm formation ability and current density, making it a promising electrode material for microbial electrochemical systems. The spray coating method is simple, cost-effective, and suitable for large-size stainless steel electrodes.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Electrochemical properties of Li-rich ternary cathode material Li1.20Mn0.44Ni0.32Co0.04O2 and its oxygen-deficient phase

Binpeng Hou, Jingjin Chen, Li-Hong Zhang, Xiaowen Shi, Zizhong Zhu

Summary: The electrochemical performance of Li1.20Mn0.44Ni0.32Co0.04O2 and its oxygen-deficient phase Li1.20Mn0.44Ni0.32Co0.04O1.83 was studied through first-principles calculations. The results show that the oxygen-deficient phase has a higher theoretical capacity but lower voltage platform and higher chemical activity compared to the pristine phase.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Post-mortem analysis of the Li-ion battery with charge/discharge deterioration in high- and low-temperature environments

Yating Du, Sayoko Shironita, Daisuke Asakura, Eiji Hosono, Yoshitsugu Sone, Yugo Miseki, Eiichi Kobayashi, Minoru Umeda

Summary: This study investigates the effect of high- and low-temperature environments on the charge-discharge performance of a Li-ion battery. The deterioration mechanisms of the battery at different temperatures are analyzed through various characterization techniques. The results indicate that the battery performance deteriorates more significantly at a low-temperature environment of 5 degrees C compared to higher temperatures. The understanding of the deterioration mechanisms can contribute to the development of safer battery usage methods.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

A Co3O4-x/Co nanocomposite with synergistically enhanced electrochemical activity for reduction of nitrite to ammonia

Si-Si Shi, Zhi-Xiang Yuan, Fei Zhang, Ping Chen

Summary: In this study, a new nano-electrocatalyst was prepared, which exhibited superior electrocatalytic activity for the reduction of NO2- to ammonia in a neutral electrolyte, potentially due to the synergistic enhancement between Co3O4-x and Co.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Facile fabrication of NaOH nanorods on pencil graphite electrode for simultaneous electrochemical detection of natural antioxidants by deep eutectic solvent

Berna Dalkiran, Havva Bekirog

Summary: This study reports the use of deep eutectic solvents (DES) based on ethylene glycol and urea as low-cost and green electrolytes for enhancing electrochemical detection of natural antioxidants. The study successfully developed a disposable and effective electrochemical sensing platform for simultaneous determination of ascorbic acid (AA) and gallic acid (GA) using NaOH nanorods on a pencil graphite electrode. The proposed electrode showed improved analytical performance, with higher peak currents and shifted oxidation potentials in DES compared to BR buffer medium.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

A three-dimensional fibrous tungsten-oxide/carbon composite derived from natural cellulose substance as an anodic material for lithium-ion batteries

Sijun Ren, Jianguo Huang

Summary: In this study, a novel bio-inspired nanofibrous WO3/carbon composite was synthesized using a facile hydrothermal method. The three-dimensional network structure of the composite alleviated the volume expansion of WO3 nanorods and enhanced the charge-transport kinetics. The optimized composite exhibited superior lithium storage properties.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Stabilizing the dissolution kinetics by interstitial Zn cations in CoMoO4 for oxygen evolution reaction at high potential

Zhilong Zheng, Yu Chen, Hongxia Yin, Hengbo Xiao, Xiangji Zhou, Zhiwen Li, Ximin Li, Jin Chen, Songliu Yuan, Junjie Guo, Haibin Yu, Zhen Zhang, Lihua Qian

Summary: This study found that interstitial Zn cations in CoMoO4 can modulate the dissolution kinetics of Mo cations and improve the OER performance. The interstitial Zn cations can prevent the dissolution of Co cations at high potential, enhancing the durability of the catalyst.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Molecular insights on optimizing nanoporous carbon-based supercapacitors with various electrolytes

Xiaobo Lin, Shern R. Tee, Debra J. Searles, Peter T. Cummings

Summary: Molecular dynamics simulations using the constant potential method were used to investigate the charging dynamics and charge storage of supercapacitors. The simulations revealed that the water-in-salt electrolyte exhibited the highest charge storage and significantly higher capacitance on the negative electrode. The varying contributions of different electrode regions to supercapacitor performance were also demonstrated.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Interaction between bilirubin oxidase and Au nanoparticles distributed over dimpled titanium foil towards oxygen reduction reaction

Wiktoria Lipinska, Vita Saska, Katarzyna Siuzdak, Jakub Karczewski, Karol Zaleski, Emerson Coy, Anne de Poulpiquet, Ievgen Mazurenko, Elisabeth Lojou

Summary: The spatial distribution of enzymes on electrodes is important for bioelectrocatalysis. In this study, controlled spatial distribution of gold nanoparticles on Ti nanodimples was achieved. The efficiency of enzymatic O2 reduction was found to be influenced by the size of the gold nanoparticles and their colocalization with TiO2. The highest stability of enzymatic current was observed with the largest gold nanoparticles.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Electrochemical supercapacitor and water splitting electrocatalysis applications of self-grown amorphous Ni(OH)2 nanosponge-balls

Tariq M. Al-Hejri, Zeenat A. Shaikh, Ahmed H. Al-Naggar, Siddheshwar D. Raut, Tabassum Siddiqui, Hamdan M. Danamah, Vijaykumar V. Jadhav, Abdullah M. Al-Enizi, Rajaram S. Mane

Summary: This study explores a promising self-growth approach for the synthesis of nickel hydroxide (Ni(OH)2) nanosponge-balls on the surface of a nickel-foam (NiF) electrode. The modified NiF electrode, named Ni(OH)2@NiF, shows distinctive nanosponge-ball morphology and demonstrates excellent energy storage capability and electrocatalytic performance in both hydrogen and oxygen evolution reactions.

ELECTROCHIMICA ACTA (2024)

Article Electrochemistry

Versatile mixed ionic-electronic conducting binders for high-power, high-energy batteries

Rafael Del Olmo, Gregorio Guzman-Gonzalez, Oihane Sanz, Maria Forsyth, Nerea Casado

Summary: The use of Lithium-Ion Batteries (LIBs) is becoming increasingly extensive, and it is important to optimize the devices to achieve their maximum practical specific capacity. In this study, mixed ionic-electronic conducting (MIEC) binders based on PEDOT:PSS and PEDOT: PDADMA-TFSI were developed for Li-ion cathodes, and their performance was compared with conventional formulations. The influence of electrode formulations, including the addition of conducting carbon and an Organic Ionic Plastic Cristal (OIPC), was also analyzed. The proposed binders showed improved performance compared to conventional formulations with different electrolyte types and active materials.

ELECTROCHIMICA ACTA (2024)