Comparative Evaluation of Cast Aluminum Alloys for Automotive Cylinder Heads: Part I—Microstructure Evolution

Comparative Evaluation of Cast Aluminum Alloys for Automotive Cylinder Heads: Part II—Mechanical and Thermal Properties

(2017) Shibayan Roy et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

High- and low-cycle fatigue influence of silicon, copper, strontium and iron on hypo-eutectic Al–Si–Cu and Al–Si–Mg cast alloys used in cylinder heads

(2016) Patrik Huter et al.   INTERNATIONAL JOURNAL OF FATIGUE

Determination of Optimum Sr Level for Eutectic Si Modification in Al–Si Cast Alloys Using Thermal analysis and Tensile Properties

(2016) Mohammadreza Zamani et al.   International Journal of Metalcasting

The influence of Cu addition and pre-straining on the natural aging and bake hardening response of Al-Mg-Si alloys

(2016) Lipeng Ding et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Effects of Sb, Sr, and Bi on the material properties of cast Al-Si-Cu alloys produced through heated mold continuous casting

(2016) Mitsuhiro Okayasu et al.   Journal of Mechanical Science and Technology

Effect of Mn addition on Fe-rich intermetallics morphology and dry sliding wear investigation of hypereutectic Al-17.5%Si alloys

(2016) Cyrus Bidmeshki et al.   Journal of Materials Research and Technology-JMR&T

In Situ Study of Microstructure Evolution in Solidification of Hypereutectic Al-Si Alloys with Application of Thermal Analysis and Neutron Diffraction

(2015) Dimitry G. Sediako et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

SDAS, Si and Cu Content, and the Size of Intermetallics in Al-Si-Cu-Mg-Fe Alloys

(2015) Tharmalingam Sivarupan et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

In situ quantification of the nucleation and growth of Fe-rich intermetallics during Al alloy solidification

(2014) C. Puncreobutr et al.   ACTA MATERIALIA

Nucleation kinetics of entrained eutectic Si in Al–5Si alloys

(2014) J.H. Li et al.   ACTA MATERIALIA

Influence of Fe-rich intermetallics on solidification defects in Al–Si–Cu alloys

(2014) C. Puncreobutr et al.   ACTA MATERIALIA

Application of cast Al–Si alloys in internal combustion engine components

(2014) Mousa Javidani et al.   INTERNATIONAL MATERIALS REVIEWS

Nucleation and Growth of Eutectic Si in Al-Si Alloys with Na Addition

(2014) J. H. Li et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Improving Thermal Stability in Cu-Containing Al-Mg-Si Alloys by Precipitate Optimization

(2014) Calin D. Marioara et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Solid-State Transformation of Iron-Rich Intermetallic Phases in Al-Cu 206 Cast Alloys During Solution Heat Treatment

(2013) K. Liu et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Alloy Composition and Dendrite Arm Spacing in Al-Si-Cu-Mg-Fe Alloys

(2013) Tharmalingam Sivarupan et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Optimization of Solution Treatment of Cast Al-7Si-0.3Mg and Al-8Si-3Cu-0.5Mg Alloys

(2013) Emma Sjölander et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

TEM study of β′ precipitate interaction mechanisms with dislocations and β′ interfaces with the aluminium matrix in Al–Mg–Si alloys

(2012) Katharina Teichmann et al.   MATERIALS CHARACTERIZATION

The heat treatment of Al–Si–Cu–Mg casting alloys

(2010) Emma Sjölander et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

The effect of shear-resistant, plate-shaped precipitates on the work hardening of Al alloys: Towards a prediction of the strength–elongation correlation

(2009) J. da Costa Teixeira et al.   ACTA MATERIALIA

Precipitation-hardening in cast AL–Si–Cu–Mg alloys

(2009) F. J. Tavitas-Medrano et al.   JOURNAL OF MATERIALS SCIENCE

On the strengthening response of aluminum alloys containing shear-resistant plate-shaped precipitates

(2008) J. da Costa Teixeira et al.   ACTA MATERIALIA

Effect of cooling rate on solidified microstructure and mechanical properties of aluminium-A356 alloy

(2008) L.Y. Zhang et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

The effects of Mn additions on the microstructure and mechanical properties of Al–Si–Cu casting alloys

(2008) J.Y. Hwang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Preparation of high quality Al TEM specimens via a double-jet electropolishing technique

(2007) Necip Ünlü   MATERIALS CHARACTERIZATION

Precipitation kinetics of Si in aluminium alloys

(2007) Fernando Lasagni et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING