Effect of Si content on the microstructure and properties of Al–Si alloys fabricated using hot extrusion

Enhanced nucleation and refinement of eutectic Si by high number-density nano-particles in Al–10Si–0.5Sb alloys

(2017) Fengxiang Guo et al.   MATERIALS & DESIGN

Simultaneous enhancements of strength and toughness in an Al-12Si alloy synthesized using selective laser melting

(2016) Jyoti Suryawanshi et al.   ACTA MATERIALIA

Microstructure and thermal conductivity of hypereutectic Al-high Si produced by casting and spray deposition

(2016) Yandong Jia et al.   JOURNAL OF MATERIALS RESEARCH

Twin-controlled growth of eutectic Si in unmodified and Sr-modified Al–12.7%Si alloys investigated by SEM/EBSD

(2015) Xiaorui Liu et al.   ACTA MATERIALIA

Tensile properties of Al–12Si matrix composites reinforced with Ti–Al-based particles

(2015) Z. Wang et al.   JOURNAL OF ALLOYS AND COMPOUNDS

The thermal expansion behaviour of SiCp/Al–20Si composites solidified under high pressures

(2015) Zunjie Wei et al.   MATERIALS & DESIGN

Influence of cryorolling on microstructure and mechanical properties of a cast hypoeutectic Al–Si alloy

(2015) R.J. Immanuel et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Preparation of Al–Si alloys by a rapid solidification and powder metallurgy route

(2015) Zhiyong Cai et al.   MATERIALS & DESIGN

Tribological and corrosion properties of Al–12Si produced by selective laser melting

(2014) K.G. Prashanth et al.   JOURNAL OF MATERIALS RESEARCH

Friction welding of Al–12Si parts produced by selective laser melting

(2014) K.G. Prashanth et al.   MATERIALS & DESIGN

Microstructure and thermal expansion behavior of spray-deposited Al–50Si

(2014) Yandong Jia et al.   MATERIALS & DESIGN

Effect of rare earth cerium addition on the microstructure and tensile properties of hypereutectic Al–20%Si alloy

(2013) Qinglin Li et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Mechanical Properties of a Low-thermal-expansion Aluminum/Silicon Composite Produced by Powder Metallurgy

(2013) Y.Q. Liu et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Silicon dissolution and interfacial characteristics in Si/Al composites fabricated by gas pressure infiltration

(2013) W. Yu et al.   MATERIALS CHEMISTRY AND PHYSICS

Microstructure and mechanical properties of Al–12Si produced by selective laser melting: Effect of heat treatment

(2013) K.G. Prashanth et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of iron on the microstructure and mechanical property of Al–Mg–Si–Mn and Al–Mg–Si diecast alloys

(2012) Shouxun Ji et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

A study of thermal expansion of Al–Mg alloy composites containing fly ash

(2011) W.A. Uju et al.   MATERIALS & DESIGN

Grain refinement of pure aluminium and Al–7Si with Al–3B master alloy

(2011) Y Birol   MATERIALS SCIENCE AND TECHNOLOGY

Effects of yttrium and heat treatment on the microstructure and tensile properties of Al–7.5Si–0.5Mg alloy

(2010) Bao Li et al.   MATERIALS & DESIGN

Spray forming of hypereutectic Al–Si alloys

(2009) C. Cui et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Microstructural refinement of a cast hypereutectic Al–30Si alloy by friction stir processing

(2009) A.G. Rao et al.   MATERIALS LETTERS

Influence of vibration on the solidification behaviour and tensile properties of an Al–18wt%Si alloy

(2008) G. Chirita et al.   MATERIALS & DESIGN