Processing–Microstructure–Crystallographic Texture–Surface Property Relationships in Friction Stir Processing of Titanium

Laser surface textured titanium alloy (Ti–6Al–4V) – Part II – Studies on bio-compatibility

(2015) Renu Kumari et al.   APPLIED SURFACE SCIENCE

Laser surface textured titanium alloy (Ti–6Al–4V): Part 1 – Surface characterization

(2015) Wilhelm Pfleging et al.   APPLIED SURFACE SCIENCE

Titanium-Nitride Coating of Orthopaedic Implants: A Review of the Literature

(2015) Ruud P. van Hove et al.   Biomed Research International

Effect of boron addition and processing of Ti–6Al–4V on corrosion behaviour and biocompatibility

(2014) S. Bahl et al.   MATERIALS TECHNOLOGY

The control of crystallographic texture in the use of magnesium as a resorbable biomaterial

(2014) Sumit Bahl et al.   RSC Advances

The importance of crystallographic texture in the use of titanium as an orthopedic biomaterial

(2014) Sumit Bahl et al.   RSC Advances

Surface nitriding on Ti–6Al–4V alloy via friction stir processing method under nitrogen atmosphere

(2013) Bo Li et al.   APPLIED SURFACE SCIENCE

On the importance of crystallographic texture in the biocompatibility of titanium based substrate

(2013) Majid Hoseini et al.   JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART A

Production of in-situ hard Ti/TiN composite surface layers on CP-Ti using reactive friction stir processing under nitrogen environment

(2013) Ali Shamsipur et al.   SURFACE & COATINGS TECHNOLOGY

An innovative fabrication of nano-HA coatings on Ti-CaP nanocomposite layer using a combination of friction stir processing and electrophoretic deposition

(2012) Hamidreza Farnoush et al.   CERAMICS INTERNATIONAL

Tribological and corrosion behavior of friction stir processed Ti-CaP nanocomposites in simulated body fluid solution

(2012) Hamidreza Farnoush et al.   Journal of the Mechanical Behavior of Biomedical Materials

An experimental study of deformation mechanism and microstructure evolution during hot deformation of Ti–6Al–2Zr–1Mo–1V alloy

(2012) D. He et al.   MATERIALS & DESIGN

Effect of microstructure on the fatigue properties of Ti–6Al–4V titanium alloys

(2012) G.Q. Wu et al.   MATERIALS & DESIGN

Dynamic recrystallization mechanisms of an Fe–8% Al low density steel under hot rolling conditions

(2012) C. Castan et al.   SCRIPTA MATERIALIA

Deformation behaviour of commercially pure titanium at extreme strain rates

(2011) N.P. Gurao et al.   ACTA MATERIALIA

Quantitative analysis of grain refinement in titanium during equal channel angular pressing

(2011) Y.J. Chen et al.   SCRIPTA MATERIALIA

Dynamic recrystallization mechanisms operating in a Ni–20%Cr alloy under hot-to-warm working

(2010) N. Dudova et al.   ACTA MATERIALIA

Superplastic deformation mechanism of an ultrafine-grained aluminum alloy produced by friction stir processing

(2010) Z.Y. Ma et al.   ACTA MATERIALIA

Texture evolution in commercially pure titanium after warm equal channel angular extrusion

(2010) Satyam Suwas et al.   ACTA MATERIALIA

Investigation of welding parameter dependent microstructure and mechanical properties in friction stir welded pure Ti joints

(2010) Hidetoshi Fujii et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Specific Character of Material Flow in Near-Surface Layer during Friction Stir Processing of AZ31 Magnesium Alloy

(2010) S. Mironov et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Development of grain structure during friction stir welding of pure titanium

(2009) S. Mironov et al.   ACTA MATERIALIA

Electrochemical corrosion behavior of magnesium and titanium alloys in simulated body fluid

(2009) A.M. Fekry et al.   ELECTROCHIMICA ACTA

Investigations on the Effects of the Tool Material, Geometry, and Tilt Angle on Friction Stir Welding of Pure Titanium

(2009) K. Reshad Seighalani et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Friction stir processing: An effective technique to refine grain structure and enhance ductility

(2009) Ehab A. El-Danaf et al.   MATERIALS & DESIGN

Deformation behaviour of commercially pure titanium during simple hot compression

(2008) Zhipeng Zeng et al.   MATERIALS & DESIGN

Friction Stir Processing Technology: A Review

(2008) Z.Y. Ma   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

XPS and EIS study of the passive film formed on orthopaedic Ti–6Al–7Nb alloy in Hank's physiological solution

(2007) I. Milošev et al.   ELECTROCHIMICA ACTA

Microstructural characteristics and mechanical properties of Ti–6Al–4V friction stir welds

(2007) Yu Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructural refinement and property enhancement of cast light alloys via friction stir processing

(2007) Z.Y. Ma et al.   SCRIPTA MATERIALIA