Effects of build orientation and thickness of allowance on the fatigue behaviour of 15-5 PH stainless steel manufactured by DMLS

Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel

(2017) Aref Yadollahi et al.   INTERNATIONAL JOURNAL OF FATIGUE

Metal Additive Manufacturing: A Review of Mechanical Properties

(2016) John J. Lewandowski et al.   Annual Review of Materials Research

The effect of aging on machinability of 15Cr–5Ni precipitation hardened stainless steel

(2016) D. Palanisamy et al.   Archives of Civil and Mechanical Engineering

Analytical modelling of residual stress in additive manufacturing

(2016) O Fergani et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Influence of the build orientation on the fatigue strength of EOS maraging steel produced by additive metal machine

(2016) D. Croccolo et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Fracture toughness and fatigue crack growth rate properties in wire + arc additive manufactured Ti-6Al-4V

(2016) X Zhang et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Influence of the engagement ratio on the shear strength of an epoxy adhesive by push-out tests on pin-and-collar joints: Part II: Campaign at different temperature levels

(2016) Dario Croccolo et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Influence of the engagement ratio on the shear strength of an epoxy adhesive by push-out tests on pin-and-collar joints: Part I: Campaign at room temperature

(2016) Dario Croccolo et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES

Material and residual stress considerations associated with the autofrettage of weld clad components

(2016) G. Benghalia et al.   INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING

Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using X-ray computed tomography

(2016) I. Maskery et al.   MATERIALS CHARACTERIZATION

Neutron diffraction measurements of residual stress in additively manufactured stainless steel

(2016) D.W. Brown et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Mechanical behavior of additive manufactured, powder-bed laser-fused materials

(2016) Todd M. Mower et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Fatigue crack propagation behaviour in wire+arc additive manufactured Ti‐6Al‐4V: Effects of microstructure and residual stress

(2016) Jikui Zhang et al.   MATERIALS & DESIGN

Effect of build direction on the fracture toughness and fatigue crack growth in selective laser melted Ti-6Al-4 V

(2015) P. Edwards et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Bending fatigue life characterisation of direct metal laser sintering nickel alloy 718

(2015) O. Scott-Emuakpor et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Thermal Aging Phenomena in Cast Duplex Stainless Steels

(2015) T. S. Byun et al.   JOM

Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg

(2015) Christian Weingarten et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

A Study on the Laser Spatter and the Oxidation Reactions During Selective Laser Melting of 316L Stainless Steel, Al-Si10-Mg, and Ti-6Al-4V

(2015) Marco Simonelli et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Fatigue Performance of Laser Additive Manufactured Ti–6Al–4V in Very High Cycle Fatigue Regime up to 109 Cycles

(2015) Eric Wycisk et al.   Frontiers in Materials

Fatigue performance evaluation of selective laser melted Ti–6Al–4V

(2014) P. Edwards et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Experimental characterization and analytical modelling of the mechanical behaviour of fused deposition processed parts made of ABS-M30

(2013) Dario Croccolo et al.   COMPUTATIONAL MATERIALS SCIENCE

A new method for modelling the support effect under rotating bending fatigue: application to Ti-6Al-4V alloy, with and without shot peening

(2013) G. Olmi et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

A comparison of the tensile, fatigue, and fracture behavior of Ti–6Al–4V and 15-5 PH stainless steel parts made by selective laser melting

(2013) H. Khalid Rafi et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

The critical distance theory for fatigue analysis of notched aluminium specimens subjected to repeated bending

(2012) B. VAN HOOREWEDER et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Low Cycle Fatigue Experiments on Turbogenerator Steels and a New Method for Defining Confidence Bands

(2012) Giorgio Olmi   JOURNAL OF TESTING AND EVALUATION

Assessing and comparing influencing factors of residual stresses in selective laser melting using a novel analysis method

(2012) Jean-Pierre Kruth et al.   PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE

Analysis of Fracture Toughness and Crack Propagation of Ti6Al4V Produced by Selective Laser Melting

(2011) Brecht Van Hooreweder et al.   ADVANCED ENGINEERING MATERIALS

Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior

(2011) Erhard Brandl et al.   MATERIALS & DESIGN

As-Fabricated and Heat-Treated Microstructures of the Ti-6Al-4V Alloy Processed by Selective Laser Melting

(2011) T. Vilaro et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Fatigue on Shot-Peened Gears: Experimentation, Simulation and Sensitivity Analyses

(2010) G. Olmi et al.   STRAIN