Advancements in Surface Reinforcement of AA2024 Alloy Using Hybridized Niobium Carbide and Ceramics Particles via FSP Technique

Correction to: Properties Augmentation of Cast Hypereutectic Al–Si Alloy Through Friction Stir Processing

(2023) William P. Bates et al.   METALS AND MATERIALS INTERNATIONAL

Effect of welding speed and wire feed rate on arc characteristics, weld bead and microstructure in standard and pulsed gas metal arc welding

(2023) Rakesh Roshan et al.   JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY

Metallurgical, mechanical and corrosion behaviour of pulsed and constant current TIG dissimilar welds of AISI 430 and Inconel 718

(2023) Balrm Yelamasetti et al.   Journal of Materials Research and Technology-JMR&T

Thermal simulation on friction stir welding of AA6061 aluminum alloy by computational fluid dynamics

(2023) Rajiv Ranjan Kumar et al.   International Journal of Interactive Design and Manufacturing - IJIDeM

Microstructure and mechanical properties of GMAW cladded AA 6063 using friction stir processing as a post-processing technique

(2023) Tejendra Singh Singhal et al.   Advances in Materials and Processing Technologies

Development of dissimilar AA2014 and AA2024 based composite with nano-Si3N4 reinforcement by friction stir process technique

(2023) Shashi Prakash Dwivedi et al.   JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY

Improvement of the microstructure and mechanical properties by hybridizing the surface of AA7075 by hexagonal boron nitride with carbide particles using the FSP process

(2022) Essam B. Moustafa et al.   Journal of Materials Research and Technology-JMR&T

The influence of reinforcement particles friction stir processing on microstructure, mechanical properties, tribological and corrosion behaviors: A review

(2022) Bo Wu et al.   Journal of Materials Research and Technology-JMR&T

Duplex and Composite Coatings: A Thematic Review on Thermal Spray Techniques and Applications

(2022) M. Sathish et al.   METALS AND MATERIALS INTERNATIONAL

Experimental investigation on surface characteristics of Ti6Al4V alloy during abrasive water jet machining process

(2022) Waheed Sami Abushanab et al.   Alexandria Engineering Journal

Improved mechanical properties of Cu8Ni4Sn alloy as functionally graded composites with preserving its thermal and electrical properties

(2022) Essam B. Moustafa et al.   MATERIALS CHEMISTRY AND PHYSICS

Fabrication and characterization of Magnesium based Mg-Titania surface composite for bioimplants

(2022) Pankaj Sonia et al.   SURFACE REVIEW AND LETTERS

Synthesis, Structural and Biomedical Characterization of Hydroxyapatite/Borosilicate Bioactive Glass Nanocomposites

(2021) Dalia E. Abulyazied et al.   Journal of Inorganic and Organometallic Polymers and Materials

Role of hybrid nanoparticles on thermal, electrical conductivity, microstructure, and hardness behavior of nanocomposite matrix

(2021) Salem S. Abdel Aziz et al.   Journal of Materials Research and Technology-JMR&T

Tribological and mechanical characteristics of AA5083 alloy reinforced by hybridising heavy ceramic particles Ta2C & VC with light GNP and Al2O3 nanoparticles

(2021) Essam B. Moustafa et al.   CERAMICS INTERNATIONAL

Microstructural, mechanical and wear behavior of A7075 surface composite reinforced with WC nanoparticle through friction stir processing

(2021) Surendra Kumar Patel et al.   Materials Science and Engineering B-Advanced Functional Solid-State Materials

Microstructural, mechanical and wear behavior of A7075 surface composite reinforced with WC and ZrSiO4 nanoparticle through friction stir processing

(2021) Surendra Kumar Patel et al.   Journal of Manufacturing Processes

The Effect of Incorporating Ceramic Particles with Different Morphologies on the Microstructure, Mechanical and Tribological Behavior of Hybrid TaC_ BN/AA2024 Nanocomposites

(2021) Emad Ismat Ghandourah et al.   Coatings

Preparation of high strength graphene reinforced Cu-based nanocomposites via mechanical alloying method: microstructural, mechanical and electrical properties

(2020) Essam B. Moustafa et al.   APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING

Effect of friction stir processing and hybrid reinforcement on wear behaviour of AA6082 alloy composite

(2020) T Satish Kumar et al.   Materials Research Express

Effect of friction stir processing on mechanical properties and heat transfer of TIG welded joint of AA6061 and AA7075

(2020) Husain Mehdi et al.   Defence Technology

Microstructure, Deformation, and Property of Wrought Magnesium Alloys

(2020) J. F. Nie et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

FTIR Spectral Characterization, Mechanical and Electrical Properties of P2O5-Li2O-CuO Glass-Ceramics

(2020) Mohammed A. Taha et al.   Silicon

Recent research progresses in Al-7075 based in-situ surface composite fabrication through friction stir processing: A review

(2020) Surendra Kumar Patel et al.   Materials Science and Engineering B-Advanced Functional Solid-State Materials

Fabrication of Hybrid Surface Composites AA6061/(B4C + MoS2) via Friction Stir Processing

(2019) Daulat Kumar Sharma et al.   JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME

Effect of tool tilt angle on strength and microstructural characteristics of friction stir welded lap joints of AA2014-T6 aluminum alloy

(2019) C. RAJENDRAN et al.   TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA

Recent progress of reinforcement materials: a comprehensive overview of composite materials

(2019) Dipen Kumar Rajak et al.   Journal of Materials Research and Technology-JMR&T

Barium titanate reinforced nickel aluminium bronze surface composite by friction stir processing

(2017) Shivraman Thapliyal et al.   MATERIALS SCIENCE AND TECHNOLOGY

Effect of SiC particle size on the physical and mechanical properties of extruded Al matrix nanocomposites

(2013) Omyma El-Kady et al.   MATERIALS & DESIGN

Hybrid effect of nanoparticles with carbon fibers on the mechanical and wear properties of polymer composites

(2011) Guo-ming Lin et al.   COMPOSITES PART B-ENGINEERING

Microstructure and Texture Evolution during Friction Stir Processing of Fully Lamellar Ti-6Al-4V

(2010) A. L. Pilchak et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE