Controlled Phase Transformation Simulations to Design Microstructure for Tailored Mechanical Properties in Steel

Effect of deformation on microstructure and mechanical properties of dual phase steel produced via strip casting simulation

(2016) Z.P. Xiong et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

The effect of martensite volume fraction on the scratch and abrasion resistance of a ferrite–martensite dual phase steel

(2016) Xiaojun Xu et al.   WEAR

Effect of martensite morphology and volume fraction on strain hardening and fracture behavior of martensite–ferrite dual phase steel

(2015) Jiecen Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Optimization of Cellular Automata Model for the Heating of Dual-Phase Steel by Genetic Algorithm and Genetic Programming

(2015) Chandan Halder et al.   MATERIALS AND MANUFACTURING PROCESSES

The influence of microstructure and composition on the plastic behaviour of dual-phase steels

(2014) A.-P. Pierman et al.   ACTA MATERIALIA

Study the effect of martensite banding on the failure initiation in dual-phase steel

(2014) A. Ramazani et al.   COMPUTATIONAL MATERIALS SCIENCE

Effects of inter-critical temperatures on martensite morphology, volume fraction and mechanical properties of dual-phase steels obtained from direct and continuous annealing cycles

(2014) Ali Ghaheri et al.   MATERIALS & DESIGN

High-efficiency fast-heating annealing of a cold-rolled dual-phase steel

(2014) Qingge Meng et al.   MATERIALS & DESIGN

A New Type of Quenching and Partitioning Processing Developed from Martensitic Pre-microstructure

(2014) Ran Ding et al.   MATERIALS AND MANUFACTURING PROCESSES

Microstructural deformation pattern and mechanical behavior analyses of DP600 dual phase steel

(2014) Hossein Hosseini-Toudeshky et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Interaction between recrystallization and phase transformation during intercritical annealing in a cold-rolled dual-phase steel: A cellular automaton model

(2013) Chengwu Zheng et al.   ACTA MATERIALIA

Deformation response of ferrite and martensite in a dual-phase steel

(2013) H. Ghassemi-Armaki et al.   ACTA MATERIALIA

Effect of heating rate on ferrite recrystallization and austenite formation of cold-roll dual phase steel

(2013) Pei Li et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Effects of ferrite volume fraction on the tensile deformation characteristics of dual phase twinning induced plasticity steel

(2013) A. Imandoust et al.   MATERIALS & DESIGN

Effect of pre-IC annealing treatments on the final microstructure and work hardening behavior of a dual-phase steel

(2013) H. Seyedrezai et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of Spot Welding Parameters on Tensile Properties of DP 600 Steel Sheet Joints

(2012) S. Aktas et al.   MATERIALS AND MANUFACTURING PROCESSES

On the Effect of Manganese on Grain Size Stability and Hardenability in Ultrafine-Grained Ferrite/Martensite Dual-Phase Steels

(2011) Marion Calcagnotto et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Quenched and Partitioned Microstructures Produced via Gleeble Simulations of Hot-Strip Mill Cooling Practices

(2011) G. A. Thomas et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Overview of Mechanisms Involved During the Quenching and Partitioning Process in Steels

(2011) M. J. Santofimia et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

New Method of Characterizing and Quantifying Complex Microstructures in Steels

(2010) A. J. DeArdo et al.   MATERIALS AND MANUFACTURING PROCESSES

Innovative Approaches in Physical Simulation and Modeling for Optimal Design and Processing of Advanced High Strength Steels

(2010) M. C. Somani et al.   MATERIALS AND MANUFACTURING PROCESSES

Rolling Technology with Reducing Resources in China

(2010) Xiang-hua Liu et al.   MATERIALS AND MANUFACTURING PROCESSES

Development of Cold-Rolled High-Strength Formable Steel for Automotive Applications

(2010) A. N. Bhagat et al.   MATERIALS AND MANUFACTURING PROCESSES

Control of Structures and Properties of Cold-Rolled Sheet Steels

(2010) Kohsaku Ushioda et al.   MATERIALS AND MANUFACTURING PROCESSES

Models for Austenite to Martensite Transformation in TRIP-Aided Steels: A Comparative Study

(2010) Monideepa Mukherjee et al.   MATERIALS AND MANUFACTURING PROCESSES

Processing Opportunities for New Advanced High-Strength Sheet Steels

(2010) David K. Matlock et al.   MATERIALS AND MANUFACTURING PROCESSES

Comparison of mechanical properties of martensite/ferrite and bainite/ferrite dual phase 4340 steels

(2009) N. Saeidi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Designing the Multiphase Microstructure of Steel for Optimal TRIP Effect: A Multiobjective Genetic Algorithm Based Approach

(2008) S. Ganguly et al.   MATERIALS AND MANUFACTURING PROCESSES

Carbon partitioning to austenite from martensite or bainite during the quench and partition (Q&P) process: A critical assessment

(2007) A.J. Clarke et al.   ACTA MATERIALIA