Effect of cryo groove rolling followed by warm rolling (CGW) on the mechanical properties of 5052 Al alloy

Effect of Cryorolling and Aging on Fatigue Behavior of Ultrafine-grained Al6061

(2015) M. Yadollahpour et al.   JOM

High-pressure torsion of thick Cu and Al–Mg–Sc ring samples

(2015) Hideaki Iwaoka et al.   JOURNAL OF MATERIALS SCIENCE

Mechanical anisotropy and microstructural changes during cryorolling of Al–Mg–Si alloy

(2015) N. Naga Krishna et al.   MATERIALS CHARACTERIZATION

Microstructural change due to isochronal annealing in severely plastic-deformed commercial purity aluminium

(2015) Yoji Miyajima et al.   PHILOSOPHICAL MAGAZINE

Effects of cold rolling and heat treatment on microstructure and mechanical properties of AA 5052 aluminum alloy

(2015) Bo WANG et al.   TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA

A Comparative Study of Commercially Pure Aluminum Processed by ECAP Using Conventional and New Die

(2014) S. Surendarnath et al.   MATERIALS AND MANUFACTURING PROCESSES

Fabrication of Nanostructured Aluminum Sheets Using Four-Layer Accumulative Roll Bonding

(2014) H. L. Yu et al.   MATERIALS AND MANUFACTURING PROCESSES

Repetitive Corrugation and Straightening of Sheet Metals

(2014) B. Ratna Sunil   MATERIALS AND MANUFACTURING PROCESSES

Effect of cryorolling and warm rolling on precipitation evolution in Al 6061 alloy

(2014) P. Nageswara Rao et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

An Ideal Ultrafine-Grained Structure for High Strength and High Ductility

(2014) C. X. Huang et al.   Materials Research Letters

Microstructures and impact toughness behavior of Al 5083 alloy processed by cryorolling and afterwards annealing

(2013) Dharmendra Singh et al.   International Journal of Minerals Metallurgy and Materials

Effect of deformation temperature on mechanical properties of ultrafine grained Al–Mg alloys processed by rolling

(2013) Dharmendra Singh et al.   MATERIALS & DESIGN

Study on cryorolled Al–Cu alloy using X-ray diffraction line profile analysis and evaluation of strengthening mechanisms

(2013) N. Naga Krishna et al.   MATERIALS & DESIGN

Mechanical properties and microstructural evolution of Al 6061 alloy processed by multidirectional forging at liquid nitrogen temperature

(2013) P. Nageswara Rao et al.   MATERIALS & DESIGN

Effect of annealing on microstructure and mechanical properties of Al 6061 alloy processed by cryorolling

(2013) P Nageswara Rao et al.   MATERIALS SCIENCE AND TECHNOLOGY

Effects of warm rolling and ageing after cryogenic rolling on mechanical properties and microstructure of Al 6061 alloy

(2012) P. Nageswara rao et al.   MATERIALS & DESIGN

Nano/Ultrafine Structured AA1100 by ARB Process

(2011) Mohammad Raei et al.   MATERIALS AND MANUFACTURING PROCESSES

Significance of stacking fault energy on microstructural evolution in Cu and Cu–Al alloys processed by high-pressure torsion

(2011) X.H. An et al.   PHILOSOPHICAL MAGAZINE

Microstructure and mechanical behavior of UFG copper processed by ECAP following different processing regimes

(2011) G. Purcek et al.   PHILOSOPHICAL MAGAZINE

The improvement of strength and ductility in ultra-fine grained 5052 Al alloy by cryogenic- and warm-rolling

(2010) U. G. Kang et al.   JOURNAL OF MATERIALS SCIENCE

Development of ultrafine-grained Al 6063 alloy by cryorolling with the optimized initial heat treatment conditions

(2010) Sushanta Kumar Panigrahi et al.   MATERIALS & DESIGN

Tensile Deformation and Fracture Mechanism of Bulk Bimodal Ultrafine-Grained Al-Mg Alloy

(2009) Zonghoon Lee et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

The evolution of homogeneity in an aluminum alloy processed using high-pressure torsion

(2008) Cheng Xu et al.   ACTA MATERIALIA

Microstructural characterization of ultrafine-grain interstitial-free steel by X-ray diffraction line profile analysis

(2008) Apu Sarkar et al.   APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING

Nanostructure and related mechanical properties of an Al–Mg–Si alloy processed by severe plastic deformation

(2008) Gulnaz Nurislamova et al.   PHILOSOPHICAL MAGAZINE LETTERS

Effect of repetitive corrugation and straightening on Al and Al–0.25Sc alloy

(2007) V. Rajinikanth et al.   MATERIALS LETTERS