Breaking the trade off between corrosion resistance and fatigue lifetime of the coated Mg alloy through cold spraying submicron-grain Al alloy coatings

Solute cluster evolution during deformation and high strain hardening capability in naturally aged Al-Zn-Mg alloy

(2021) Peng Zhang et al.   ACTA MATERIALIA

Solid-state additive manufacturing high performance aluminum alloy 6061 enabled by an in-situ micro-forging assisted cold spray

(2020) Ying-Kang Wei et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Dynamic evolution of oxide scale on the surfaces of feed stock particles from cracking and segmenting to peel-off while cold spraying copper powder having a high oxygen content

(2020) Xiao-Tao Luo et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Modification of surface hardness, wear resistance and corrosion resistance of cold spray Al coated AZ31B Mg alloy using cold spray double layered Ta/Ti coating in 3.5 wt%NaCl solution

(2020) M. Daroonparvar et al.   CORROSION SCIENCE

Simultaneous enhancement of stress- and strain-controlled fatigue properties in 316L stainless steel with gradient nanostructure

(2019) Y.B. Lei et al.   ACTA MATERIALIA

Fatigue life of micro-arc oxidation coated AA2024-T3 and AA7075-T6 alloys

(2019) Weibing Dai et al.   INTERNATIONAL JOURNAL OF FATIGUE

Revealing the evolution of microstructure, mechanical property and corrosion behavior of 7A46 aluminum alloy with different ageing treatment

(2019) Yaru Liu et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Deposition of fully dense Al-based coatings via in-situ micro-forging assisted cold spray for excellent corrosion protection of AZ31B magnesium alloy

(2019) Ying-Kang Wei et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Correlating particle impact condition with microstructure and properties of the cold-sprayed metallic deposits

(2019) Yujuan Li et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Mesoscale modeling of jet initiation behavior and microstructural evolution during cold spray single particle impact

(2019) Sumit Suresh et al.   ACTA MATERIALIA

Formation of refined grains below 10 nm in size and nanoscale interlocking in the particle–particle interfacial regions of cold sprayed pure aluminum

(2019) Zhiying Liu et al.   SCRIPTA MATERIALIA

Corrosion resistant nickel coating with strong adhesion on AZ31B magnesium alloy prepared by an in-situ shot-peening-assisted cold spray

(2018) Ying-Kang Wei et al.   CORROSION SCIENCE

On the severe localized corrosion susceptibility of the AA2198-T851 alloy

(2018) João Victor de Sousa Araujo et al.   CORROSION SCIENCE

Turning a native or corroded Mg alloy surface into an anti-corrosion coating in excited CO2

(2018) Yuecun Wang et al.   Nature Communications

Effect of volume fraction of gradient nanograined layer on high-cycle fatigue behavior of Cu

(2018) Lijun Jing et al.   SCRIPTA MATERIALIA

Comment on ‘Adiabatic shear instability is not necessary for adhesion in cold spray’

(2018) H. Assadi et al.   SCRIPTA MATERIALIA

Effect of in-situ micro-arc oxidation coating on the galvanic corrosion of AZ31Mg coupled to aluminum alloys

(2018) Li-jing Bai et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Improved fatigue resistance of gradient nanograined Cu

(2018) Jianzhou Long et al.   ACTA MATERIALIA

Fundamentals and advances in magnesium alloy corrosion

(2017) M. Esmaily et al.   PROGRESS IN MATERIALS SCIENCE

Characteristics of 7055Al alloy powders manufactured by gas-solid two-phase atomization: A comparison with gas atomization process

(2017) Chaorun Si et al.   MATERIALS & DESIGN

Cold spraying – A materials perspective

(2016) H. Assadi et al.   ACTA MATERIALIA

Failure of metals II: Fatigue

(2016) André Pineau et al.   ACTA MATERIALIA

Optimization of In-Situ Shot-Peening-Assisted Cold Spraying Parameters for Full Corrosion Protection of Mg Alloy by Fully Dense Al-Based Alloy Coating

(2016) Ying-Kang Wei et al.   JOURNAL OF THERMAL SPRAY TECHNOLOGY

Fatigue behaviors of AISI 316L stainless steel with a gradient nanostructured surface layer

(2015) H.W. Huang et al.   ACTA MATERIALIA

The origins of high hardening and low ductility in magnesium

(2015) Zhaoxuan Wu et al.   NATURE

Ready for the road

(2015) Gerald S. Frankel   NATURE MATERIALS

A high-specific-strength and corrosion-resistant magnesium alloy

(2015) Wanqiang Xu et al.   NATURE MATERIALS

Microstructure and mechanical property of Ti and Ti6Al4V prepared by an in-situ shot peening assisted cold spraying

(2015) Xiao-Tao Luo et al.   MATERIALS & DESIGN

Making strong nanomaterials ductile with gradients

(2014) K. Lu   SCIENCE

High velocity impact induced microstructure evolution during deposition of cold spray coatings: A review

(2014) Xiao-Tao Luo et al.   SURFACE & COATINGS TECHNOLOGY

Mechanism of corrosion protection of hot-dip aluminium–silicon coatings on steel studied by electrochemical depth profiling

(2013) Iris De Graeve et al.   CORROSION SCIENCE

Mechanical and Microstructural Characterization of Cold-Sprayed Ti-6Al-4V After Heat Treatment

(2013) P. Vo et al.   JOURNAL OF THERMAL SPRAY TECHNOLOGY

Microstructure and corrosion performance of a cold sprayed aluminium coating on AZ91D magnesium alloy

(2010) Yongshan Tao et al.   CORROSION SCIENCE

Fatigue behavior of PVD coated Ti–6Al–4V alloy

(2010) M.Y.P. Costa et al.   INTERNATIONAL JOURNAL OF FATIGUE

Corrosion resistance of thermally sprayed Al and Al/SiC coatings on Mg

(2009) M. Campo et al.   SURFACE & COATINGS TECHNOLOGY