A study of the cell morphology and mechanical properties of bumper material PP-T-EPDM composite foam

Towards novel super-elastic foams based on isoperene rubber: Preparation and characterization

(2020) Ali Vahidifar et al.   POLYMERS FOR ADVANCED TECHNOLOGIES

Polysilazane as a new foaming agent to prepare high-strength, low-density epoxy foam

(2019) Yucheng Chang et al.   Royal Society Open Science

The Impact of Mould Temperature and Blowing Agent Content on Structure and Properties of Injection Moulded Parts

(2018) Elzbieta Bociaga et al.   CELLULAR POLYMERS

Investigation of the mold-filling phenomenon in high-pressure foam injection molding and its effects on the cellular structure in expanded foams

(2018) Mike Tromm et al.   POLYMER

Characterization of Different Chemical Blowing Agents and Their Applicability to Produce Poly(Lactic Acid) Foams by Extrusion

(2018) Ákos Kmetty et al.   Applied Sciences-Basel

Polyoxymethylene foam: From an investigation of key factors related to porous morphologies and microstructure to the optimization of foam properties

(2016) Nantinee Mantaranon et al.   POLYMER

Foam injection molding of poly(lactic) acid: Effect of back pressure on morphology and mechanical properties

(2015) Valentina Volpe et al.   JOURNAL OF APPLIED POLYMER SCIENCE

EFFECTS OF CHEMICAL FOAMING AGENTS ON THE PHYSICO-MECHANICAL PROPERTIES AND RHEOLOGICAL BEHAVIOR OF BAMBOO POWDER-POLYPROPYLENE FOAMED COMPOSITES

(2014) Xiaxing Zhou et al.   BioResources

Influence of foam agent content and talc filler on the microcellular and mechanical properties of injection molded polypropylene and talc filled polypropylene composite foams

(2014) SH Yetgin et al.   JOURNAL OF CELLULAR PLASTICS

Physical and mechanical properties of foamed HDPE/wheat straw flour/nanoclay hybrid composite

(2013) Ishagh Babaei et al.   COMPOSITES PART B-ENGINEERING

Effect of chemical blowing agent on the hygroscopic behavior of HDPE/rice husk flour composites

(2012) Behzad Kord   JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS

Foaming of linear isotactic polypropylene based on its non-isothermal crystallization behaviors under compressed CO2

(2011) Da-Chao Li et al.   JOURNAL OF SUPERCRITICAL FLUIDS

Effect of chemical blowing agent on cell structure and mechanical properties of EPDM foam, and peel strength and thermal conductivity of wood/NR composite–EPDM foam laminates

(2009) W. Yamsaengsung et al.   COMPOSITES PART B-ENGINEERING

Effect of organoclay on the mechanical / thermal properties of microcellular injection molded polystyrene–clay nanocomposites

(2009) Shyh-shin Hwang et al.   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

Study of microcellular injection-molded polypropylene/waste ground rubber tire powder blend

(2009) Zhen Xiang Xin et al.   MATERIALS & DESIGN

The effect of injection molding conditions on the morphology of polymer structural foams

(2009) M. Reza Barzegari et al.   POLYMER ENGINEERING AND SCIENCE

Advanced structural foam molding using a continuous polymer/gas melt flow stream

(2008) Xiang Xu et al.   JOURNAL OF APPLIED POLYMER SCIENCE

Current Trends in Nanocomposite Foams

(2008) Christopher C. Ibeh et al.   JOURNAL OF CELLULAR PLASTICS

Development of CO2 for polymer foam applications

(2008) David L. Tomasko et al.   JOURNAL OF SUPERCRITICAL FLUIDS

Effect of Processing Parameters on the Mechanical Properties of Injection Molded Thermoplastic Polyolefin (TPO) Cellular Foams

(2008) Steven Wong et al.   MACROMOLECULAR MATERIALS AND ENGINEERING