Mechanical characterization and fatigue assessment of wire and arc additively manufactured HSLA steel parts
Published 2022 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
Mechanical characterization and fatigue assessment of wire and arc additively manufactured HSLA steel parts
Authors
Keywords
-
Journal
INTERNATIONAL JOURNAL OF FATIGUE
Volume 164, Issue -, Pages 107146
Publisher
Elsevier BV
Online
2022-07-17
DOI
10.1016/j.ijfatigue.2022.107146
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Low cycle fatigue behavior of wire arc additive manufactured and solution annealed 308 L stainless steel
- (2022) Yajing Li et al. Additive Manufacturing
- Probabilistic strain-fatigue life performance based on stochastic analysis of structural and waam-stainless steels
- (2021) Haohui Xin et al. ENGINEERING FAILURE ANALYSIS
- Fatigue of Wire+Arc Additive Manufactured Ti-6Al-4V in Presence of Process-Induced Porosity Defects
- (2021) Emre Akgun et al. INTERNATIONAL JOURNAL OF FATIGUE
- Defect-correlated fatigue resistance of additively manufactured Al-Mg4.5Mn alloy with in situ micro-rolling
- (2021) Cheng Xie et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Influence of deposition strategies on tensile and fatigue properties in a wire + arc additive manufactured Ti-6Al-4V
- (2021) Abdul Khadar Syed et al. INTERNATIONAL JOURNAL OF FATIGUE
- In-situ SEM investigation and modeling of small crack growth behavior of additively manufactured titanium alloy
- (2021) Xinyan Wang et al. INTERNATIONAL JOURNAL OF FATIGUE
- Fatigue crack growth behaviour of wire and arc additively manufactured ER70S-6 low carbon steel components
- (2021) Anna Ermakova et al. INTERNATIONAL JOURNAL OF FRACTURE
- Experimental investigation of the fatigue crack growth behavior in wire arc additively manufactured ER100S‐1 steel specimens
- (2021) Anna Ermakova et al. FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES
- Fatigue crack growth behaviour of an Al-Mg4.5Mn alloy fabricated by hybrid in situ rolled wire + arc additive manufacturing
- (2021) Zhen Liao et al. INTERNATIONAL JOURNAL OF FATIGUE
- Monotonic and Fatigue Properties of Steel Material Manufactured by Wire Arc Additive Manufacturing
- (2020) Michael Wächter et al. Applied Sciences-Basel
- Criticality of porosity defects on the fatigue performance of wire + arc additive manufactured titanium alloy
- (2019) Romali Biswal et al. INTERNATIONAL JOURNAL OF FATIGUE
- Current Status and Perspectives on Wire and Arc Additive Manufacturing (WAAM)
- (2019) Tiago A. Rodrigues et al. Materials
- Enhancement in fatigue performance of metastable austenitic stainless steel through directed energy deposition additive manufacturing
- (2019) Jerard Gordon et al. MATERIALS & DESIGN
- Relationship between manufacturing defects and fatigue properties of additive manufactured austenitic stainless steel
- (2019) Thale R. Smith et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Analysis of fracture toughness properties of wire + arc additive manufactured high strength low alloy structural steel components
- (2019) Philip Dirisu et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Revisiting fundamental welding concepts to improve additive manufacturing: From theory to practice
- (2019) J.P. Oliveira et al. PROGRESS IN MATERIALS SCIENCE
- Effect of LCF on behavior and microstructure of microalloyed HSLA steel and its simulated CGHAZ
- (2019) Vujadin Aleksić et al. ENGINEERING FAILURE ANALYSIS
- Formation mechanism and control methods of acicular ferrite in HSLA steels: A review
- (2018) Yi Shao et al. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
- Fatigue crack growth anisotropy, texture and residual stress in austenitic steel made by wire and arc additive manufacturing
- (2018) J.V. Gordon et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Formation and improvement of surface waviness for additive manufacturing 5A06 aluminium alloy component with GTAW system
- (2018) Haibin Geng et al. RAPID PROTOTYPING JOURNAL
- Non-destructive microstructural analysis by electrical conductivity: comparison with hardness measurements in different materials
- (2018) Gonçalo L. Sorger et al. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
- Metal Additive Manufacturing: A Review of Mechanical Properties
- (2016) John J. Lewandowski et al. Annual Review of Materials Research
- Design for Additive Manufacturing: Trends, opportunities, considerations, and constraints
- (2016) Mary Kathryn Thompson et al. CIRP ANNALS-MANUFACTURING TECHNOLOGY
- Fracture toughness and fatigue crack growth rate properties in wire + arc additive manufactured Ti-6Al-4V
- (2016) X Zhang et al. FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES
- Special zone in multi-layer and multi-pass welded metal and its role in the creep behavior of 9Cr 1Mo welded joint
- (2016) Wen Liu et al. MATERIALS & DESIGN
- Fatigue crack propagation behaviour in wire+arc additive manufactured Ti‐6Al‐4V: Effects of microstructure and residual stress
- (2016) Jikui Zhang et al. MATERIALS & DESIGN
- Additive manufacturing using plasma transferred arc
- (2015) E. A. Alberti et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- A study of the mechanical properties of objects built through weld-deposition
- (2013) Simhambhatla Suryakumar et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
Find Funding. Review Successful Grants.
Explore over 25,000 new funding opportunities and over 6,000,000 successful grants.
ExploreAdd your recorded webinar
Do you already have a recorded webinar? Grow your audience and get more views by easily listing your recording on Peeref.
Upload Now