Numerical and experimental investigation on thermo-mechanically induced residual stress in high-speed milling of Ti-6Al-4V alloy
Published 2022 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
Numerical and experimental investigation on thermo-mechanically induced residual stress in high-speed milling of Ti-6Al-4V alloy
Authors
Keywords
Finite element model, Cutting forces, Cutting temperature, Chip morphology, Residual stresses, Nano-hardness, High-speed milling
Journal
Journal of Manufacturing Processes
Volume 76, Issue -, Pages 575-587
Publisher
Elsevier BV
Online
2022-03-01
DOI
10.1016/j.jmapro.2022.02.039
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- In-process detection of cutting forces and cutting temperature signals in cryogenic assisted turning of titanium alloys: An analytical approach and experimental study
- (2022) Munish Kumar Gupta et al. MECHANICAL SYSTEMS AND SIGNAL PROCESSING
- Improvement of machinability of Ti and its alloys using cooling-lubrication techniques: A review and future prospect
- (2021) Danil Yu. Pimenov et al. Journal of Materials Research and Technology-JMR&T
- Application of pre-stressed cutting to aviation alloy: The effect on residual stress and surface roughness
- (2021) Peng Ruitao et al. Journal of Manufacturing Processes
- Microstructural and mechanical property investigation of machined surface layer in high-speed milling of Ti-6Al-4V alloy
- (2021) Irfan Ullah et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- FEM analysis of thermal and residual stress profile in selective laser melting of 316L stainless steel
- (2021) Saad Waqar et al. Journal of Manufacturing Processes
- Investigation on residual stress evolution in nickel-based alloy affected by multiple cutting operations
- (2021) Yang Liu et al. Journal of Manufacturing Processes
- Cutting forces and temperature measurements in cryogenic assisted turning of AA2024-T351 alloy: An experimentally validated simulation approach
- (2021) Munish Kumar Gupta et al. MEASUREMENT
- Influence of hybrid Cryo-MQL lubri-cooling strategy on the machining and tribological characteristics of Inconel 718
- (2021) Mohd Danish et al. TRIBOLOGY INTERNATIONAL
- Numerical investigation on serrated chip formation during high-speed milling of Ti-6Al-4V alloy
- (2021) Irfan Ullah et al. Journal of Manufacturing Processes
- An experimental investigation of hybrid manufactured SLM based Al-Si10-Mg alloy under mist cooling conditions
- (2021) Monsuru Ramoni et al. Journal of Manufacturing Processes
- A state-of-the-art review on tool wear and surface integrity characteristics in machining of superalloys
- (2021) Murat Sarıkaya et al. CIRP Journal of Manufacturing Science and Technology
- Evolution of residual stress behavior in selective laser melting (SLM) of 316L stainless steel through preheating and in-situ re-scanning techniques
- (2021) Saad Waqar et al. OPTICS AND LASER TECHNOLOGY
- Tribological and thermal behavior with wear identification in contact interaction of the Ti6Al4V-sintered carbide with AlTiN coatings pair
- (2021) Marta Bogdan-Chudy et al. TRIBOLOGY INTERNATIONAL
- Numerical investigation of thermal behavior and melt pool morphology in multi-track multi-layer selective laser melting of the 316L steel
- (2020) Saad Waqar et al. The International Journal of Advanced Manufacturing Technology
- Investigation into the surface quality and stress corrosion cracking resistance of AISI 316L stainless steel via precision end-milling operation
- (2020) Muhammad Yasir et al. The International Journal of Advanced Manufacturing Technology
- Sustainable milling of Ti–6Al–4V: A trade-off between energy efficiency, carbon emissions and machining characteristics under MQL and cryogenic environment
- (2020) Muhammad Jamil et al. JOURNAL OF CLEANER PRODUCTION
- An analytical model of residual stress in orthogonal cutting based on the radial return method
- (2019) S.Q. Wang et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Finite element simulation study on pre-stress multi-step cutting of Ti-6Al-4V titanium alloy
- (2019) Xuhao Song et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Analytical modeling of machining-induced residual stresses in milling of complex surface
- (2019) Ruihu Zhou et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- FE temperature- and residual stress prediction in milling inserts and correlation with experimentally observed damage mechanisms
- (2018) Andreas W. Nemetz et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Modelling of phase transformations induced by thermo-mechanical loads considering stress-strain effects in hard milling of AISI H13 steel
- (2018) Binxun Li et al. INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
- Efficient Multiscale Modeling and Validation of Residual Stress Field in Cutting
- (2017) F. Wang et al. JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME
- Hybrid modeling with finite element and statistical methods for residual stress prediction in peripheral milling of titanium alloy Ti-6Al-4V
- (2016) Dong Yang et al. INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
- Prediction of cutting speed interval of diamond-coated tools with residual stress
- (2016) Mehmet Aydin MATERIALS AND MANUFACTURING PROCESSES
- The effect of tool nose radius on surface integrity and residual stresses when turning Inconel 718™
- (2015) A.R.C. Sharman et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Investigations on the chip formation mechanism and shear localization sensitivity of high-speed machining Ti6Al4V
- (2014) Bing Wang et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Influence of cutting edge radius on surface integrity and burr formation in milling titanium
- (2012) Carl-Frederik Wyen et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Finite element simulation of high-speed machining of titanium alloy (Ti–6Al–4V) based on ductile failure model
- (2011) Guang Chen et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- A numerical model incorporating the microstructure alteration for predicting residual stresses in hard machining of AISI 52100 steel
- (2010) D. Umbrello et al. CIRP ANNALS-MANUFACTURING TECHNOLOGY
- Machining induced surface integrity in titanium and nickel alloys: A review
- (2010) Durul Ulutan et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- An experimental and numerical study on the face milling of Ti–6Al–4V alloy: Tool performance and surface integrity
- (2010) Balkrishna Rao et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- SURFACE INTEGRITY CHARACTERIZATION AND PREDICTION IN MACHINING OF HARDENED AND DIFFICULT-TO-MACHINE ALLOYS: A STATE-OF-ART RESEARCH REVIEW AND ANALYSIS
- (2009) Y. B. Guo et al. MACHINING SCIENCE AND TECHNOLOGY
- A comprehensive experimental study on surface integrity by end milling Ti–6Al–4V
- (2008) J. Sun et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
Discover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversationCreate your own webinar
Interested in hosting your own webinar? Check the schedule and propose your idea to the Peeref Content Team.
Create Now