The feasibility of printing polylactic acid-nanohydroxyapatite composites using a low-cost fused deposition modeling 3D printer

Experimental Validation of Plastic Mandible Models Produced by a “Low-Cost” 3-Dimensional Fused Deposition Modeling Printer

(2016) Federico Maschio et al.   MEDICAL SCIENCE MONITOR

3D Printing Surgical Implants at the clinic: A Experimental Study on Anterior Cruciate Ligament Reconstruction

(2016) An Liu et al.   Scientific Reports

Conductive 3D microstructures by direct 3D printing of polymer/carbon nanotube nanocomposites via liquid deposition modeling

(2015) Giovanni Postiglione et al.   COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING

Three-Dimensional Printing of Drug-Eluting Implants: Preparation of an Antimicrobial Polylactide Feedstock Material

(2015) Jorrit Jeroen Water et al.   JOURNAL OF PHARMACEUTICAL SCIENCES

Recent advances in 3D printing of biomaterials

(2015) Helena N Chia et al.   Journal of Biological Engineering

Development and characterization of UV curable epoxy/hydroxyapatite suspensions for stereolithography applied to bone tissue engineering

(2014) Francesca Scalera et al.   CERAMICS INTERNATIONAL

Organically modified montmorillonite polymer nanocomposites for stereolithography building process

(2014) C. Esposito Corcione et al.   POLYMERS FOR ADVANCED TECHNOLOGIES

Bone tissue engineering using 3D printing

(2013) Susmita Bose et al.   Materials Today

Fabrication aspects of PLA-CaP/PLGA-CaP composites for orthopedic applications: A review

(2012) Huan Zhou et al.   Acta Biomaterialia

Combination therapy with BMP-2 and BMSCs enhances bone healing efficacy of PCL scaffold fabricated using the 3D plotting system in a large segmental defect model

(2012) Sun-Woong Kang et al.   BIOTECHNOLOGY LETTERS

Influence of the calcination temperature on morphological and mechanical properties of highly porous hydroxyapatite scaffolds

(2012) F. Scalera et al.   CERAMICS INTERNATIONAL

Biodegradable and bioactive porous scaffold structures prepared using fused deposition modeling

(2012) Jyrki Korpela et al.   JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART B-APPLIED BIOMATERIALS

Scaffolds for bone tissue engineering fabricated from two different materials by the rapid prototyping technique: PCL versus PLGA

(2012) So Hee Park et al.   JOURNAL OF MATERIALS SCIENCE-MATERIALS IN MEDICINE

Bioprinting of a mechanically enhanced three-dimensional dual cell-laden construct for osteochondral tissue engineering using a multi-head tissue/organ building system

(2012) Jin-Hyung Shim et al.   JOURNAL OF MICROMECHANICS AND MICROENGINEERING

Rapid casting of patterned vascular networks for perfusable engineered three-dimensional tissues

(2012) Jordan S. Miller et al.   NATURE MATERIALS

Rapid-prototyped PLGA/β-TCP/hydroxyapatite nanocomposite scaffolds in a rabbit femoral defect model

(2012) Jinku Kim et al.   Biofabrication

Influence of stone particles on the rheological behavior of a novel photopolymerizable siloxane-modified acrylic resin

(2011) C. Esposito Corcione et al.   JOURNAL OF APPLIED POLYMER SCIENCE

Fused deposition modeling of patient‐specific polymethylmethacrylate implants

(2010) David Espalin et al.   RAPID PROTOTYPING JOURNAL

Evaluation of chondrocyte growth in the highly porous scaffolds made by fused deposition manufacturing (FDM) filled with type II collagen

(2008) Hung-Jen Yen et al.   BIOMEDICAL MICRODEVICES

Blended PCL/PLGA scaffold fabrication using multi-head deposition system

(2008) Jong Young Kim et al.   MICROELECTRONIC ENGINEERING

Synthesis and characterization of clay-nanocomposite solvent-based polyurethane adhesives

(2007) C. Esposito Corcione et al.   INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES