Revealing the decomposition mechanisms of dislocations and metastable α' phase and their effects on mechanical properties in a Ti-6Al-4V alloy

Effect of high pressure torsion process on the microhardness, microstructure and tribological property of Ti6Al4V alloy

(2021) Guanyu Deng et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Effects of heating rate on the alloy element partitioning and mechanical properties in equiaxed α+β Ti-6Al-4V alloy

(2021) Jinhu Zhang et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Nonadditive strengthening functions for cold-worked cubic metals: Experiments and constitutive modeling

(2020) Fulin Jiang et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Re-epithelialization and immune cell behaviour in an ex vivo human skin model

(2020) Ana Rakita et al.   Scientific Reports

Insight into Si poisoning on grain refinement of Al-Si/Al-5Ti-B system

(2020) Yang Li et al.   ACTA MATERIALIA

Thermodynamics and kinetics of phase transformation in rare earth–magnesium alloys: A critical review

(2020) Qun Luo et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Effect of cryogenic quenching on microstructure and microhardness of Ti-6Al-4V alloy

(2020) Shashank Shukla et al.   MATERIALS LETTERS

Anti-phase boundary energy of β series precipitates in Mg-Y-Nd system

(2020) Yanlin Guo et al.   SCRIPTA MATERIALIA

Effects of intermittent loading time and stress ratio on dwell fatigue behavior of titanium alloy Ti-6Al-4V ELI used in deep-sea submersibles

(2020) Chengqi Sun et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Accelerated flow softening and dynamic transformation of Ti-6Al-4V alloy in two-phase region during hot deformation via coarsening α grain

(2019) Xiankun Ji et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Static coarsening behaviour of lamellar microstructure in selective laser melted Ti–6Al–4V

(2019) Sheng Cao et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Effect of double stage solution treatment on the volume fraction of massive phase (αm) as a new method to obtain a fine lamellar α/β in Ti–6Al–4V alloy

(2019) Ghozali Suprobo et al.   INTERMETALLICS

Twinning and sequential kinking in lamellar Ti-6Al-4V alloy

(2019) Xiaodong Zheng et al.   ACTA MATERIALIA

On the role of cooling rate and temperature in forming twinned α’ martensite in Ti–6Al–4V

(2019) Sheng Cao et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Effect of dislocation distribution on the yield stress in ferritic steel under identical dislocation density conditions

(2019) Yuki Tanaka et al.   SCRIPTA MATERIALIA

Environmental fatigue crack propagation behavior of β-annealed Ti-6Al-4V alloy in NaCl solution under controlled potentials

(2018) Soojin Ahn et al.   INTERNATIONAL JOURNAL OF FATIGUE

Effect of the Surface Layer Strained by Mechanical Grinding on X-ray Diffraction Analysis

(2018) Fulin Jiang et al.   ISIJ INTERNATIONAL

Role of martensite decomposition in tensile properties of selective laser melted Ti-6Al-4V

(2018) Sheng Cao et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Influence of alloy element partitioning on strength of primary α phase in Ti-6Al-4V alloy

(2018) L.R. Zeng et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Effect of stabilization annealing on SCC susceptibility of β-annealed Ti-6Al-4V alloy in 0.6 M NaCl solution

(2018) Daeho Jeong et al.   METALS AND MATERIALS INTERNATIONAL

Influence of α/β interface phase on the tensile properties of laser cladding deposited Ti–6Al–4V titanium alloy

(2017) Zhuang Zhao et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Comprehensive Determination of Kinetic Parameters in Solid-State Phase Transitions: An Extended Jonhson–Mehl–Avrami–Kolomogorov Model with Analytical Solutions

(2016) Yuepeng Pang et al.   CRYSTAL GROWTH & DESIGN

Influence of cooling rate following heat treatment on microstructure and phase transformation for a two-phase alloy

(2016) Jianwei Xu et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Effect of prior martensite on bainite transformation in nanobainite steel

(2015) W. Gong et al.   ACTA MATERIALIA

The origins of high hardening and low ductility in magnesium

(2015) Zhaoxuan Wu et al.   NATURE

Effect of cooling rate on mechanism of β→α phase transformation on continuous cooling in Ti–5Ta–1.8Nb alloy

(2012) Madhusmita Behera et al.   JOURNAL OF ALLOYS AND COMPOUNDS

On the mechanical properties and microstructure of commercially pure Al fabricated by semi-constrained groove pressing

(2011) S. Morattab et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Room-temperature ductility of Ti–6Al–4V alloy with α′ martensite microstructure

(2010) Hiroaki Matsumoto et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING