Damage evolution of 7075 aluminum alloy basing the Gurson Tvergaard Needleman model under high temperature conditions

Hot damage evolution in a high strength aluminum alloy during hot forming: a study using the Gurson–Tvergaard–Needleman model

(2021) Xiangji Li et al.   Journal of Materials Research and Technology-JMR&T

Stress and fracture surface analysis of uncoated and coated 7075-T6 specimens under the rotating bending fatigue loading

(2020) S. Baragetti et al.   ENGINEERING FAILURE ANALYSIS

Effects of contact body temperature and holding time on the microstructure and mechanical properties of 7075 aluminum alloy in contact solid solution treatment

(2020) Zhiqiang Zhang et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Hot tensile properties, microstructure evolution and fracture mechanisms of Ti-6Al-4V alloy with initial coarse equiaxed phases

(2020) Yu-Qiang Jiang et al.   MATERIALS CHARACTERIZATION

Meso-mechanics and damage evolution of AA5182-O aluminum alloy sheet Based on the GTN model

(2020) Gui Li et al.   ENGINEERING FRACTURE MECHANICS

Effects of deformation parameters and stress triaxiality on the fracture behaviors and microstructural evolution of an Al-Zn-Mg-Cu alloy

(2020) Y.C. Lin et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Experimental Investigation of GTN model parameters of 6061 Al alloy

(2020) R.A. Yildiz et al.   EUROPEAN JOURNAL OF MECHANICS A-SOLIDS

Process modeling and optimization for biomass steam-gasification employing response surface methodology

(2020) Sk Arafat Zaman et al.   BIOMASS & BIOENERGY

Response surface methodology as a predictive tool for the fabrication of coatings with optimal anti-fogging performance

(2020) Iván Rodríguez Durán et al.   THIN SOLID FILMS

Ductile fracture behavior of ECAP deformed AZ61 magnesium alloy based on response surface methodology and finite element simulation

(2019) Addisu Negash Ali et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Ductile crack growth behaviors at different locations of a weld joint for an X80 pipeline steel: A numerical investigation using GTN models

(2019) Bin Qiang et al.   ENGINEERING FRACTURE MECHANICS

Effect of tool coatings on the interfacial heat transfer coefficient in hot stamping of aluminium alloys under variable contact pressure conditions

(2019) Xiaochuan Liu et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Mechanism of increasing spinnability by multi-pass spinning forming – Analysis of damage evolution using a modified GTN model

(2019) He Wu et al.   INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES

On the thermal forming limit diagram (TFLD) with GTN mesoscopic damage model for AA7075 aluminum alloy: Numerical and experimental investigation

(2019) Liang Ying et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Parameter window for assisted crack tip flipping: Studied by a shear extended Gurson model

(2019) K.L. Nielsen et al.   INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES

Combining the finite element method and response surface methodology for optimization of shot peening parameters

(2019) Xiaoli Wang et al.   INTERNATIONAL JOURNAL OF FATIGUE

Experimental and numerical investigation of ductile fracture using GTN damage model on in-situ tensile tests

(2019) H. Gholipour et al.   INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES

An extended GTN model for low stress triaxiality and application in spinning forming

(2018) He Wu et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Ductile fracture prediction in aluminium alloy 5A06 sheet forming based on GTN damage model

(2017) Bugang Teng et al.   ENGINEERING FRACTURE MECHANICS

The formability investigation of CNT-reinforced aluminum nano-composite sheets manufactured by accumulative roll bonding

(2017) M. R. Morovvati et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Tearing failure of ultra-thin sheet-metal involving size effect in blanking process: Analysis based on modified GTN model

(2017) Shen Wang et al.   INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES

Damage prediction in single point incremental forming using an extended Gurson model

(2017) Carlos Felipe Guzmán et al.   INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES

Residual stress field analysis of Al/steel butt joint using laser welding–brazing

(2017) Jiankang Huang et al.   MATERIALS SCIENCE AND TECHNOLOGY

Identification of the “Overburning” Phenomenon for Alloy 2014 Semiproducts

(2017) P. L. Reznik et al.   METAL SCIENCE AND HEAT TREATMENT

Modified GTN model for a broad range of stress states and application to ductile fracture

(2016) Wei Jiang et al.   EUROPEAN JOURNAL OF MECHANICS A-SOLIDS

The impact of the Chinese automotive industry: scenarios based on the national environmental goals

(2015) Yijie Liu et al.   JOURNAL OF CLEANER PRODUCTION

Influence of microstructure on work-hardening and ductile fracture of aluminium alloys

(2015) Ketill O. Pedersen et al.   MATERIALS & DESIGN

An extended GTN model for ductile fracture under high and low stress triaxiality

(2013) L. Malcher et al.   INTERNATIONAL JOURNAL OF PLASTICITY

The initiation and propagation of edge cracks of silicon steel during tandem cold rolling process based on the Gurson–Tvergaard–Needleman damage model

(2012) Yuxi Yan et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Application of response surface methodology to drive GTN model parameters and determine the FLD of tailor welded blank

(2011) M. Abbasi et al.   COMPUTATIONAL MATERIALS SCIENCE