The study of hot deformation on laser cladding remanufactured 316L stainless steel

Three-dimensional maps of geometrically necessary dislocation densities in additively manufactured Ni-based superalloy IN718

(2020) Wyatt A. Witzen et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Study on microstructure and tensile properties of 316L stainless steel fabricated by CMT wire and arc additive manufacturing

(2020) C. Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

A Comparison Study of Constitutive Equation, Neural Networks, and Support Vector Regression for Modeling Hot Deformation of 316L Stainless Steel

(2020) Shin-Hyung Song   Materials

Study of the Effects of Hot Forging on the Additively Manufactured Stainless Steel Preforms

(2020) Catalin I. Pruncu et al.   Journal of Manufacturing Processes

Correlation between arc mode, microstructure, and mechanical properties during wire arc additive manufacturing of 316L stainless steel

(2019) Leilei Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Laser additive manufacturing of Zn-2Al part for bone repair: Formability, microstructure and properties

(2019) Cijun Shuai et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Additive Manufacturing in Repair – Influence of Processing Parameters on Properties of Inconel 718

(2019) Bonny Onuike et al.   MATERIALS LETTERS

Repairing additive-manufactured 316L stainless steel using direct energy deposition

(2019) Wook Jin Oh et al.   OPTICS AND LASER TECHNOLOGY

Investigation on the Hot Deformation Behavior of 316L Stainless Steel Using 3D Processing Map

(2019) Le-li Chen et al.   TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS

Application of Directed Energy Deposition-Based Additive Manufacturing in Repair

(2019) Abdollah Saboori et al.   Applied Sciences-Basel

Experimental and crystal plasticity study on deformation bands in single crystal and multi-crystal pure aluminium

(2019) Qinmeng Luan et al.   ACTA MATERIALIA

Quantitative multiscale correlative microstructure analysis of additive manufacturing of stainless steel 316L processed by selective laser melting

(2019) Matjaž Godec et al.   MATERIALS CHARACTERIZATION

A new grain orientation spread approach to analyze the dynamic recrystallization behavior of a cast-homogenized Mg-Zn-Zr alloy using electron backscattered diffraction

(2018) A. Hadadzadeh et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

High Strength and Ductility of Additively Manufactured 316L Stainless Steel Explained

(2018) Md. Shamsujjoha et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Anisotropy and heterogeneity of microstructure and mechanical properties in metal additive manufacturing: A critical review

(2018) Y. Kok et al.   MATERIALS & DESIGN

Using transmission Kikuchi diffraction in a scanning electron microscope to quantify geometrically necessary dislocation density at the nanoscale

(2018) X.Z. Liang et al.   ULTRAMICROSCOPY

Microstructure and fatigue crack growth of EA4T steel in laser cladding remanufacturing

(2017) WenJing Chen et al.   ENGINEERING FAILURE ANALYSIS

Additive manufacturing of fatigue resistant materials: Challenges and opportunities

(2017) Aref Yadollahi et al.   INTERNATIONAL JOURNAL OF FATIGUE

A comparison on metallurgical behaviors of 316L stainless steel by selective laser melting and laser cladding deposition

(2017) Mingming Ma et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Joining of Inconel 718 and 316 Stainless Steel using electron beam melting additive manufacturing technology

(2016) Alejandro Hinojos et al.   MATERIALS & DESIGN

Anisotropic tensile behavior of Ti–6Al–4V components fabricated with directed energy deposition additive manufacturing

(2015) Beth E. Carroll et al.   ACTA MATERIALIA

Wire-feed additive manufacturing of metal components: technologies, developments and future interests

(2015) Donghong Ding et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

The orientation and strain dependence of dislocation structure evolution in monotonically deformed polycrystalline copper

(2015) Jun Jiang et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Mechanical Properties and Microstructural Features of Direct Laser-Deposited Ti-6Al-4V

(2015) Linkan Bian et al.   JOM

Effects of process time interval and heat treatment on the mechanical and microstructural properties of direct laser deposited 316L stainless steel

(2015) Aref Yadollahi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Laser powder bed fusion additive manufacturing of metals; physics, computational, and materials challenges

(2015) W. E. King et al.   Applied Physics Reviews

Laser cladding as repair technology for Ti–6Al–4V alloy: Influence of building strategy on microstructure and hardness

(2015) H. Paydas et al.   MATERIALS & DESIGN

Evolution of dislocation density distributions in copper during tensile deformation

(2013) J. Jiang et al.   ACTA MATERIALIA

Characterization of stainless steel parts by Laser Metal Deposition Shaping

(2013) Kai Zhang et al.   MATERIALS & DESIGN

60 Years of Hall-Petch: Past to Present Nano-Scale Connections

(2013) Ronald W. Armstrong   MATERIALS TRANSACTIONS

Study on microstructure and mechanical properties of 304 stainless steel joints by TIG, laser and laser-TIG hybrid welding

(2009) Jun Yan et al.   OPTICS AND LASERS IN ENGINEERING

Resolving the geometrically necessary dislocation content by conventional electron backscattering diffraction

(2008) W. Pantleon   SCRIPTA MATERIALIA