Performance evaluation of tool coatings and nanofluid MQL on the micro-machinability of Ti-6Al-4V
Published 2021 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
Performance evaluation of tool coatings and nanofluid MQL on the micro-machinability of Ti-6Al-4V
Authors
Keywords
Micromilling, Minimum quantity lubrication, Ti-6Al-4V, Nanofluids, Coating delamination
Journal
Journal of Manufacturing Processes
Volume 73, Issue -, Pages 595-610
Publisher
Elsevier BV
Online
2021-11-27
DOI
10.1016/j.jmapro.2021.11.030
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Use and performance of soybean oil based bio-lubricant in reducing specific cutting energy during biomimetic machining
- (2021) Xiaobin Cui et al. Journal of Manufacturing Processes
- Cumulative reduction of friction and size effects in micro milling through proper selection of coating thickness of TiAlN coated tool: Experimental and analytical assessments
- (2021) Priyabrata Sahoo et al. Journal of Manufacturing Processes
- Determination of minimum uncut chip thickness and size effects in micro-milling of P-20 die steel using surface quality and process signal parameters
- (2020) Priyabrata Sahoo et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Multi-objective optimization of MQL mist parameters for eco-friendly grinding
- (2020) Akash Subhash Awale et al. Journal of Manufacturing Processes
- Bio-inspired design of cleaner interrupted turning and its effects on specific cutting energy and harmful gas emission
- (2020) Xiaobin Cui et al. JOURNAL OF CLEANER PRODUCTION
- Machinability performance of nickel alloy X-750 with SiAlON ceramic cutting tool under dry, MQL and hBN mixed nanofluid-MQL
- (2020) Şenol Şirin et al. TRIBOLOGY INTERNATIONAL
- The influence of additive manufacturing on the micromilling machinability of Ti6Al4V: A comparison of SLM and commercial workpieces
- (2020) Fábio de Oliveira Campos et al. Journal of Manufacturing Processes
- Effects of hybrid Al2O3-CNT nanofluids and cryogenic cooling on machining of Ti–6Al–4V
- (2019) Muhammad Jamil et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Tool wear analysis in micromilling of titanium alloy
- (2019) Alessandro Colpani et al. PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY
- Influence of minimum quantity lubrication on surface integrity of ground hardened H13 hot die steel
- (2018) A. S. Awale et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Cutting Performance of Different Coated Micro End Mills in Machining of Ti-6Al-4V
- (2018) Zhiqiang Liang et al. Micromachines
- Finite difference simulation and experimental investigation: effects of physical synergetic properties of nanoparticles on temperature distribution and surface integrity of workpiece in nanofluid MQL grinding process
- (2017) Mohammadreza Shabgard et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Effect of Interaction of Nanoparticles and Surfactants on the Spreading Dynamics of Sessile Droplets
- (2017) A. R. Harikrishnan et al. LANGMUIR
- Preparation, characterization and tribological mechanism of nanofluids
- (2017) Linghui Kong et al. RSC Advances
- Effect of lubrication on machining response and dynamic instability in high-speed micromilling of Ti-6Al-4V
- (2017) Rinku K. Mittal et al. Journal of Manufacturing Processes
- Finish turning of Ti-6Al-4V with the atomization-based cutting fluid (ACF) spray system
- (2017) Chandra Nath et al. Journal of Manufacturing Processes
- Novel uses of alumina-MoS 2 hybrid nanoparticle enriched cutting fluid in hard turning of AISI 304 steel
- (2017) Anuj Kumar Sharma et al. Journal of Manufacturing Processes
- Analytical modeling and experimental validation of residual stress in micro-end-milling
- (2016) F. Y. Peng et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Performance of water-based TiO 2 nanofluid during the minimum quantity lubrication machining of aluminium alloy, AA6061-T6
- (2016) M.S. Najiha et al. JOURNAL OF CLEANER PRODUCTION
- Cutting performance of nano-crystalline diamond (NCD) coating in micro-milling of Ti 6 Al 4 V alloy
- (2016) K. Aslantas et al. PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY
- Performance evaluation of Ti–6Al–4V grinding using chip formation and coefficient of friction under the influence of nanofluids
- (2015) Dinesh Setti et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Analyzing effects of cooling and lubrication conditions in micromilling of Ti6Al4V
- (2015) Elisa Vazquez et al. JOURNAL OF CLEANER PRODUCTION
- Nanofluids Alter the Surface Wettability of Solids
- (2015) Sangwook Lim et al. LANGMUIR
- Effect of tool coating materials on surface roughness in micromachining of Inconel 718 super alloy
- (2014) İrfan Ucun et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- The effect of minimum quantity lubrication and cryogenic pre-cooling on cutting performance in the micro milling of Inconel 718
- (2014) İrfan Ucun et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Effect of fluid concentration in titanium machining with an atomization-based cutting fluid (ACF) spray system
- (2013) Chandra Nath et al. Journal of Manufacturing Processes
- Nano-Cutting Fluid for Enhancement of Metal Cutting Performance
- (2012) S. Khandekar et al. MATERIALS AND MANUFACTURING PROCESSES
- Identification of factors that dominate size effect in micro-machining
- (2011) A.J Mian et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- An experimental evaluation of graphite nanoplatelet based lubricant in micro-milling
- (2010) A. Marcon et al. CIRP ANNALS-MANUFACTURING TECHNOLOGY
- Tool edge radius effect on cutting temperature in micro-end-milling process
- (2010) Kai Yang et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Evaluation and selection of hard coatings for micro milling of hardened tool steel
- (2008) A. Aramcharoen et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Some studies on high-pressure cooling in turning of Ti–6Al–4V
- (2008) A.K. Nandy et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
Find the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
SearchCreate your own webinar
Interested in hosting your own webinar? Check the schedule and propose your idea to the Peeref Content Team.
Create Now