FFF 3D Printing in Electronic Applications: Dielectric and Thermal Properties of Selected Polymers

Analysis of FDM and DLP 3D-Printing Technologies to Prototype Electromagnetic Devices for RFID Applications

(2021) Riccardo Colella et al.   SENSORS

Investigating the Material Properties and Microstructural Changes of Fused Filament Fabricated PLA and Tough-PLA Parts

(2021) Nida Naveed   Polymers

Polymer 3D Printing Review: Materials, Process, and Design Strategies for Medical Applications

(2021) Amit M. E. Arefin et al.   Polymers

Design of an instrumented microwave multimode cavity for sintering of nuclear ceramics

(2021) J. Croquesel et al.   MATERIALS & DESIGN

Accelerated Alkaline Attack of 3D Printing Polymers to Assess Their Durability in Geopolymer-Based Matrices

(2021) Henrique A. Santana et al.   JOURNAL OF MATERIALS IN CIVIL ENGINEERING

Two coatings that enhance mechanical properties of fused filament-fabricated carbon-fiber reinforced composites

(2020) S. Barone et al.   Additive Manufacturing

Mechanical evaluation of polymeric filaments and their corresponding 3D printed samples

(2020) A.M. Oviedo et al.   POLYMER TESTING

Investigation of infill-patterns on mechanical response of 3D printed poly-lactic-acid

(2020) Bandar Aloyaydi et al.   POLYMER TESTING

The mechanical testing and performance analysis of polymer-fibre composites prepared through the additive manufacturing

(2020) Vigneshwaran Shanmugam et al.   POLYMER TESTING

Effects of auxiliary heat on warpage and mechanical properties in carbon fiber/ABS composite manufactured by fused deposition modeling

(2020) Ning Yu et al.   MATERIALS & DESIGN

Inkjet-Printed Electronics on Paper for RF Identification (RFID) and Sensing

(2020) Sangkil Kim   Electronics

Novel mechanical models of tensile strength and elastic property of FDM AM PLA materials: Experimental and theoretical analyses

(2019) Yu Zhao et al.   MATERIALS & DESIGN

Fabrication of poly(lactic acid)/Ti composite scaffolds with enhanced mechanical properties and biocompatibility via fused filament fabrication (FFF)–based 3D printing

(2019) Jina Lee et al.   Additive Manufacturing

Enhancing the interlayer tensile strength of 3D printed short carbon fiber reinforced PETG and PLA composites via annealing

(2019) Sunil Bhandari et al.   Additive Manufacturing

FDM process parameters influence over the mechanical properties of polymer specimens: A review

(2018) Diana Popescu et al.   POLYMER TESTING

PLA conductive filament for 3D printed smart sensing applications

(2018) Simone Luigi Marasso et al.   RAPID PROTOTYPING JOURNAL

Modelling, and characterization of 3D printed cellular structures

(2018) Michał Kucewicz et al.   MATERIALS & DESIGN

Experimental characterization of the mechanical properties of 3D-printed ABS and polycarbonate parts

(2017) Jason T. Cantrell et al.   RAPID PROTOTYPING JOURNAL

3D Printed Electronics With High Performance, Multi-Layered Electrical Interconnect

(2017) Chiyen Kim et al.   IEEE Access

Mechanical characterization of 3D printed polymers for fiber reinforced polymers processing

(2017) Daniel-Alexander Türk et al.   MATERIALS & DESIGN

Conductive 3D microstructures by direct 3D printing of polymer/carbon nanotube nanocomposites via liquid deposition modeling

(2015) Giovanni Postiglione et al.   COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING

3D Printing multifunctionality: structures with electronics

(2014) David Espalin et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

3D Printing for the Rapid Prototyping of Structural Electronics

(2014) Eric Macdonald et al.   IEEE Access

A Simple, Low-Cost Conductive Composite Material for 3D Printing of Electronic Sensors

(2012) Simon J. Leigh et al.   PLoS One

An overview of the recent developments in polylactide (PLA) research

(2010) K. Madhavan Nampoothiri et al.   BIORESOURCE TECHNOLOGY