A probabilistic approach for high cycle fatigue of Wire and Arc Additive Manufactured parts taking into account process-induced pores

Effect of pulsed metal inert gas (pulsed-MIG) and cold metal transfer (CMT) techniques on hydrogen dissolution in wire arc additive manufacturing (WAAM) of aluminium

(2020) Karan S. Derekar et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Evaluation of tandem controlled short-circuit GMAW for improved deposition in additive manufacture of large Nickel Aluminium Bronze naval components

(2020) A. Queguineur et al.   Welding in the World

Microstructure and mechanical properties of wire arc additively manufactured Hastelloy C276 alloy

(2020) Zhijun Qiu et al.   MATERIALS & DESIGN

Effect of initial microstructure on the deformation heterogeneities of 316L stainless steels fabricated by selective laser melting processing

(2020) Amol B. Kale et al.   Journal of Materials Research and Technology-JMR&T

A high-performance WAAM process for Al–Mg–Mn using controlled short-circuiting metal transfer at increased wire feed rate and increased travel speed

(2020) Oleg Panchenko et al.   MATERIALS & DESIGN

Criticality of porosity defects on the fatigue performance of wire + arc additive manufactured titanium alloy

(2019) Romali Biswal et al.   INTERNATIONAL JOURNAL OF FATIGUE

Interpretation of the fatigue anisotropy of additively manufactured TA6V alloys via a fracture mechanics approach

(2019) Viet-Duc Le et al.   ENGINEERING FRACTURE MECHANICS

Fatigue properties of AlSi10Mg obtained by additive manufacturing: Defect-based modelling and prediction of fatigue strength

(2018) S. Romano et al.   ENGINEERING FRACTURE MECHANICS

Surface roughness effects on the fatigue strength of additively manufactured Ti-6Al-4V

(2018) Jonathan Pegues et al.   INTERNATIONAL JOURNAL OF FATIGUE

Additive manufacturing using WAAM with AA5183 wire

(2018) A. Horgar et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Residual stress and texture control in Ti-6Al-4V wire + arc additively manufactured intersections by stress relief and rolling

(2018) J.R. Hönnige et al.   MATERIALS & DESIGN

The influence of build parameters and wire batch on porosity of wire and arc additive manufactured aluminium alloy 2319

(2018) E.M. Ryan et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

A spatial periodicity of microstructural evolution and anti-indentation properties of wire-arc additive manufacturing 2Cr13 thin-wall part

(2018) Jinguo Ge et al.   MATERIALS & DESIGN

Development of a stochastic approach for fatigue life prediction of AlSi12 alloy processed by selective laser melting

(2017) Shafaqat Siddique et al.   ENGINEERING FAILURE ANALYSIS

Very high cycle fatigue and fatigue crack propagation behavior of selective laser melted AlSi12 alloy

(2017) Shafaqat Siddique et al.   INTERNATIONAL JOURNAL OF FATIGUE

Identification of the micro-plasticity mechanisms at the origin of self-heating under cyclic loading with low stress amplitude

(2017) Rémi Munier et al.   INTERNATIONAL JOURNAL OF FATIGUE

On estimating axial high cycle fatigue behavior by rotating beam fatigue testing: Application to A356 aluminum alloy castings

(2017) Hüseyin Özdeş et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components

(2017) S. Tammas-Williams et al.   Scientific Reports

A Comparative Study of Additively Manufactured Thin Wall and Block Structure with Al-6.3%Cu Alloy Using Cold Metal Transfer Process

(2017) Baoqiang Cong et al.   Applied Sciences-Basel

Qualification of AM parts: Extreme value statistics applied to tomographic measurements

(2017) S. Romano et al.   MATERIALS & DESIGN

Influence of second phases on fatigue crack growth behavior of nickel aluminum bronze

(2016) Xiaoyan Xu et al.   INTERNATIONAL JOURNAL OF FATIGUE

Wire + Arc Additive Manufacturing

(2016) S. W. Williams et al.   MATERIALS SCIENCE AND TECHNOLOGY

Fabricating Superior NiAl Bronze Components through Wire Arc Additive Manufacturing

(2016) Donghong Ding et al.   Materials

A comparative study of additive manufacturing techniques: Residual stress and microstructural analysis of CLAD and WAAM printed Ti–6Al–4V components

(2016) Blanka A. Szost et al.   MATERIALS & DESIGN

Influence of process-induced microstructure and imperfections on mechanical properties of AlSi12 processed by selective laser melting

(2015) Shafaqat Siddique et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Investigation of the Microstructure and Corrosion Properties of Friction Stir Processed Cast NiAl Bronze

(2015) Yuting Lv et al.   MATERIALS TRANSACTIONS

Fatigue Strength Prediction for Titanium Alloy TiAl6V4 Manufactured by Selective Laser Melting

(2015) Stefan Leuders et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy

(2014) Baoqiang Cong et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Determination of high cycle fatigue properties of a wide range of steel sheet grades from self-heating measurements

(2014) Rémi Munier et al.   INTERNATIONAL JOURNAL OF FATIGUE

A new approach to characterizing and modeling the high cycle fatigue properties of cast materials based on self-heating measurements under cyclic loadings

(2012) Anthony Ezanno et al.   INTERNATIONAL JOURNAL OF FATIGUE

Microstructure and Mechanical Properties of Wire and Arc Additive Manufactured Ti-6Al-4V

(2012) Fude Wang et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Probabilistic multiscale models and measurements of self-heating under multiaxial high cycle fatigue

(2010) M. Poncelet et al.   JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS