Enhanced high-cycle fatigue strength of Al–12Si–4Cu-1.2Mn-T6 cast aluminum alloy at room temperature and 350 C

Fatigue behavior of AW7075 aluminum alloy in ultra-high cycle fatigue region

(2020) S. Fintová et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of constraint factor on the thermo-mechanical fatigue behavior of an Al-Si eutectic alloy

(2020) M. Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Distinct fatigue limit of a 6XXX series aluminum alloy in relation to crack tip strain-aging

(2020) Yoshimasa Takahashi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effects of microstructural heterogeneity on fatigue properties of cast aluminum alloys

(2020) Yi-nan Jiao et al.   Journal of Central South University

High temperature fatigue of heat treated secondary AlSi7Cu3Mg alloys

(2020) Alessandro De Mori et al.   INTERNATIONAL JOURNAL OF FATIGUE

The effect of Ni-doping on the microstructure, hot deformation behavior, and processing map of as-cast Al–Si piston alloy

(2020) M. Mirzaee-Moghadam et al.   Journal of Materials Science

Joint effect of micro-sized Si particles and nano-sized dispersoids on the flow behavior and dynamic recrystallization of near-eutectic Al–Si based alloys during hot compression

(2020) Yuna Wu et al.   JOURNAL OF ALLOYS AND COMPOUNDS

The influence of defect and temperature on the fatigue behaviours of Al‐Si‐Cu‐Mg‐Ni alloy

(2019) Haiquan Liu et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Ni-Rich Phases in Al-12%Si-4%Cu-1.2%Mn-x%Ni Heat-Resistant Alloys and Effect of Ni-Alloying on Tensile Mechanical Properties

(2019) Hengcheng Liao et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Experimental investigation on the effect of shot peening on contact fatigue strength for carburized and quenched gears

(2018) Wei Li et al.   INTERNATIONAL JOURNAL OF FATIGUE

Peritectic reaction between two primary Mn-rich phases during solidification of Al-Si-Cu-Mn heat-resistant alloy and the effect of cooling rate on it

(2018) Guangjing Li et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Formation of Al15Mn3Si2 Phase During Solidification of a Novel Al-12%Si-4%Cu-1.2%Mn Heat-Resistant Alloy and Its Thermal Stability

(2018) Xiaojing Suo et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Fatigue crack growth under large scale yielding condition in a cast automotive aluminum alloy

(2018) Sebastien Dezecot et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of friction stir processing on the room temperature fatigue cracking mechanisms of A356 aluminum alloy

(2018) Phalgun Nelaturu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

An approach to correlate fatigue crack growth rate with S-N curve for an aluminum alloy LY12CZ

(2018) Shanqin Hou et al.   THEORETICAL AND APPLIED FRACTURE MECHANICS

Effect of temperature on the growth of fatigue surface cracks in aluminum alloys

(2018) V.N. Shlyannikov et al.   THEORETICAL AND APPLIED FRACTURE MECHANICS

Effects of Mg Content on the Fatigue Strength and Fracture Behavior of Al-Si-Mg Casting Alloys

(2018) Ming-Ze Wu et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Improving the fatigue strength of A7N01 aluminum alloy by adjusting Si content

(2018) B.S. Gong et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Dispersoid particles precipitated during the solutionizing course of Al-12 wt%Si-4 wt%Cu-1.2 wt%Mn alloy and their influence on high temperature strength

(2017) Hengcheng Liao et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

The role of elevated temperature exposure on structural evolution and fatigue strength of eutectic AlSi12 alloys

(2016) R. Konečná et al.   INTERNATIONAL JOURNAL OF FATIGUE

High- and low-cycle fatigue influence of silicon, copper, strontium and iron on hypo-eutectic Al–Si–Cu and Al–Si–Mg cast alloys used in cylinder heads

(2016) Patrik Huter et al.   INTERNATIONAL JOURNAL OF FATIGUE

Thermo-mechanical fatigue influence of copper and silicon on hypo-eutectic Al–Si–Cu and Al–Si–Mg cast alloys used in cylinder heads

(2016) Patrik Huter et al.   INTERNATIONAL JOURNAL OF FATIGUE

Strain Ratio Effects on Low-Cycle Fatigue Behavior of Gravity Cast Al-Si-Cu Alloys

(2015) K. L. Fan et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Application of cast Al–Si alloys in internal combustion engine components

(2014) Mousa Javidani et al.   INTERNATIONAL MATERIALS REVIEWS

Microstructure, tensile properties and fracture behavior of high temperature Al–Si–Mg–Cu cast alloys

(2013) A.M.A. Mohamed et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of Fe content and microstructural features on the tensile and fatigue properties of the Al–Si10–Cu2 alloy

(2011) Lorella Ceschini et al.   MATERIALS & DESIGN

Mechanical properties of intermetallic phases in multi-component Al–Si alloys using nanoindentation

(2009) C.-L. Chen et al.   INTERMETALLICS

Investigation of mechanical properties of intermetallic phases in multi-component Al–Si alloys using hot-stage nanoindentation

(2009) C.-L. Chen et al.   INTERMETALLICS

Microstructure, tensile and fatigue properties of the Al–10%Si–2%Cu alloy with different Fe and Mn content cast under controlled conditions

(2009) Lorella Ceschini et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY