A unique three-stage dependence of yielding behavior and strain-hardening ability in Ti-10V-2Fe-3Al alloy on phase fraction

Tuning the strength and ductility balance of a TRIP titanium alloy

(2020) Benjamin Ellyson et al.   SCRIPTA MATERIALIA

Deformation mechanism of bimodal microstructure in Ti-6Al-4V alloy: The effects of intercritical annealing temperature and constituent hardness

(2020) Yan Chong et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Effect of structural stability on the stress induced martensitic transformation in Ti-10V-2Fe-3Al alloy

(2019) Lichun Qi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Yielding nature and Hall-Petch relationships in Ti-6Al-4V alloy with fully equiaxed and bimodal microstructures

(2019) Yan Chong et al.   SCRIPTA MATERIALIA

Factors determining room temperature mechanical properties of bimodal microstructures in Ti-6Al-4V alloy

(2018) Yan Chong et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

On the heterogeneous nature of deformation in a strain-transformable beta metastable Ti-V-Cr-Al alloy

(2018) L. Lilensten et al.   ACTA MATERIALIA

Mechanical properties of fully martensite microstructure in Ti-6Al-4V alloy transformed from refined beta grains obtained by rapid heat treatment (RHT)

(2017) Yan Chong et al.   SCRIPTA MATERIALIA

Simultaneously enhanced strength and ductility of Mg-Zn-Zr-Ca alloy with fully recrystallized ultrafine grained structures

(2017) Ruixiao Zheng et al.   SCRIPTA MATERIALIA

Combination of dynamic transformation and dynamic recrystallization for realizing ultrafine-grained steels with superior mechanical properties

(2016) Lijia Zhao et al.   Scientific Reports

The influence of β phase stability on deformation mode and compressive mechanical properties of Ti–10V–3Fe–3Al alloy

(2015) Mansur Ahmed et al.   ACTA MATERIALIA

Effect of the martensite distribution on the strain hardening and ductile fracture behaviors in dual-phase steel

(2014) Kyosun Park et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Perspectives on Titanium Science and Technology

(2013) Dipankar Banerjee et al.   ACTA MATERIALIA

Enhancement of athermal α″ martensitic transformation in Ti–10V–2Fe–3Al alloy due to high-speed hot deformation

(2012) Toshiyuki Akanuma et al.   SCRIPTA MATERIALIA

Influence of α morphology and volume fraction on the stress-induced martensitic transformation in Ti–10V–2Fe–3Al

(2011) C. Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Deformation and fracture mechanisms in fine- and ultrafine-grained ferrite/martensite dual-phase steels and the effect of aging

(2010) Marion Calcagnotto et al.   ACTA MATERIALIA

The effect of strain rate on trigger stress for stress-induced martensitic transformation and yield strength in Ti–18Al–8Nb alloy

(2010) Archana Paradkar et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Deformation-induced microstructure refinement in primary α phase-containing Ti–10V–2Fe–3Al alloy

(2010) Wei Chen et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Plasticity induced transformation in a metastableβTi-1023 alloy by controlled heat treatments

(2009) S. Neelakantan et al.   MATERIALS SCIENCE AND TECHNOLOGY

Effect of Volume Fraction of Primary α 2 on the Trigger Stress for Stress-Induced Martensitic Transformation in Two-Phase Ti-Al-Nb Alloys

(2008) Archana Paradkar et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Trigger Stress for Stress-Induced Martensitic Transformation during Tensile Deformation in Ti-Al-Nb Alloys: Effect of Grain Size

(2008) Archana Paradkar et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Effect of Al and Nb on the trigger stress for stress-induced martensitic transformation during tensile loading in Ti–Al–Nb alloys

(2007) Archana Paradkar et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING