Realization of synergistic enhancement for fracture strength and ductility by adding TiC particles in wire and arc additive manufacturing 2219 aluminium alloy

Realization of structural evolution in grain boundary, solute redistribution and improved mechanical properties by adding TiCnps in wire and arc additive manufacturing 2219 aluminium alloy

(2021) Peng Jin et al.   Journal of Materials Research and Technology-JMR&T

Interface formation and bonding control in high-volume-fraction (TiC+TiB2)/Al composites and their roles in enhancing properties

(2021) Hong-Yu Yang et al.   COMPOSITES PART B-ENGINEERING

Simultaneously enhanced strength and ductility of Al matrix composites through the introduction of intragranular nano-sized graphene nanoplates

(2021) Tielong Han et al.   COMPOSITES PART B-ENGINEERING

The strengthening mechanism and deformation behavior of Mg–Li matrix composite reinforced by Al3La phase formed in-situ through La2O3 particle

(2021) Xiaoqiang Li et al.   COMPOSITES PART B-ENGINEERING

Hot deformation induced microstructural evolution in local-heterogeneous wire + arc additive manufactured 2219 Al alloy

(2021) Yinghui Zhou et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Outstanding strengthening behavior and dynamic mechanical properties of in-situ Al–Al3Ni composites by Cu addition

(2020) Jeong Tae Kim et al.   COMPOSITES PART B-ENGINEERING

Effects of brass coating and nano-SiO2 coating on steel fiber–matrix interfacial properties of cement-based composite

(2020) Zhenyu Pi et al.   COMPOSITES PART B-ENGINEERING

High-strength Damascus steel by additive manufacturing

(2020) Philipp Kürnsteiner et al.   NATURE

Welding and additive manufacturing with nanoparticle-enhanced aluminum 7075 wire

(2020) Daniel Oropeza et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Microstructure evolution and mechanical properties of in-situ Ti6Al4V–TiB composites manufactured by selective laser melting

(2020) Zhiguang Zhou et al.   COMPOSITES PART B-ENGINEERING

Structural, mechanical and thermal characteristics of Al-Cu-Li particle reinforced Al-matrix composites synthesized by microwave sintering and hot extrusion

(2019) M. Penchal Reddy et al.   COMPOSITES PART B-ENGINEERING

Promoting the columnar to equiaxed transition and grain refinement of titanium alloys during additive manufacturing

(2019) M.J. Bermingham et al.   ACTA MATERIALIA

Wetting of liquid copper on TC4 titanium alloy and 304 stainless steel at 1273–1433 K

(2019) Qingjie Sun et al.   MATERIALS & DESIGN

Influence of travel speed on microstructure and mechanical properties of wire + arc additively manufactured 2219 aluminum alloy

(2019) Yinghui Zhou et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Novel dynamic compressive and ballistic properties in 7075-T6 Al-matrix hybrid composite reinforced with SiC and B4C particulates

(2019) Min Chul Jo et al.   COMPOSITES PART B-ENGINEERING

Automated quantification of reinforcement dispersion in B4C/Al metal matrix composites

(2019) Byeongjin Park et al.   COMPOSITES PART B-ENGINEERING

Studies on micro structural characteristics, mechanical and tribological behaviours of boron carbide and cow dung ash reinforced aluminium (Al 7075) hybrid metal matrix composite

(2019) R. Manikandan et al.   COMPOSITES PART B-ENGINEERING

Micropore evolution in additively manufactured aluminum alloys under heat treatment and inter-layer rolling

(2019) Jianglong Gu et al.   MATERIALS & DESIGN

Composition and automated crystal orientation mapping of rapid solidification products in hypoeutectic Al-4 at.%Cu alloys

(2018) K.W. Zweiacker et al.   ACTA MATERIALIA

Additive manufacturing (3D printing): A review of materials, methods, applications and challenges

(2018) Tuan D. Ngo et al.   COMPOSITES PART B-ENGINEERING

Enhanced strength and ductility at room and elevated temperatures of Al-Cu alloy matrix composites reinforced with bimodal-sized TiC p compared with monomodal–sized TiC p

(2018) Wei-Si Tian et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Optimization of the solidification conditions by means of beam oscillation during laser beam welding of aluminum

(2018) Christian Hagenlocher et al.   MATERIALS & DESIGN

3D printing of high-strength aluminium alloys

(2017) John H. Martin et al.   NATURE

The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys

(2016) Jianglong Gu et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy

(2016) Jianglong Gu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Mechanical properties of 2219-Al components produced by additive manufacturing with TIG

(2015) J. Y. Bai et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Processing and properties of magnesium containing a dense uniform dispersion of nanoparticles

(2015) Lian-Yi Chen et al.   NATURE

Fundamentals of Solidification in Aluminum Castings

(2015) Geoffrey K. Sigworth   International Journal of Metalcasting

Nanostructured high-strength molybdenum alloys with unprecedented tensile ductility

(2013) G. Liu et al.   NATURE MATERIALS

Wetting of TiC by molten Al at 1123–1323K

(2010) Qiaoli Lin et al.   ACTA MATERIALIA