The Improved Mechanical Anisotropy of a Commercial Al–Cu–Mg–Mn–Si (2017) Aluminum Alloy by Cross rolling

Ageing response of cold-rolled Al–Cu–Mg alloy

(2020) Ivan S. Zuiko et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

The Role of Interfaces on the Deformation Mechanisms in Bimodal Al Laminates Produced by Accumulative Roll Bonding

(2020) Heinz-Werner Höppel et al.   ADVANCED ENGINEERING MATERIALS

Microstructure evolution, plastic anisotropy, and intergranular corrosion of Al-Mg-Si sheet processed through a combination of hot extrusion and cold rolling

(2020) Zhigang Li et al.   MATERIALS CHARACTERIZATION

Influence of equal channel angular pressing on the evolution of microstructures, aging behavior and mechanical properties of as-quenched Al-6.6Zn-1.25Mg alloy

(2019) Fuqing Jiang et al.   MATERIALS CHARACTERIZATION

Tensile properties, microstructures and fracture behaviors of an Al-Zn-Mg-Cu alloy during ageing after solution treating and cold-rolling

(2018) Hai Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

A continuum dislocation-based model of wedge microindentation of single crystals

(2018) Giacomo Po et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Effect of cross-rolling on microstructure and texture evolution and tensile behavior of aluminium-copper-lithium (AA2195) alloy

(2018) Niraj Nayan et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Coupling of dislocations and precipitates: Impact on the mechanical behavior of ultrafine grained Al–Zn–Mg alloys

(2016) Kaka Ma et al.   ACTA MATERIALIA

The dependence of microstructure, texture evolution and mechanical properties of Al–Mg–Si–Cu alloy sheet on final cold rolling deformation

(2016) Xiaofeng Wang et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Effects of re-ageing treatment on microstructure and tensile properties of solution treated and cold-rolled Al–Cu–Mg alloys

(2016) Hai Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Novel Fabrication of Bulk Fine-Grained Al-Cu-Mg Alloy with Superior Mechanical Properties 

(2015) Ruixiao Zheng et al.   ADVANCED ENGINEERING MATERIALS

Microstructure and anisotropic mechanical behavior of friction stir welded AA2024 alloy sheets

(2015) Zhihan Zhang et al.   MATERIALS CHARACTERIZATION

Mechanical anisotropy and microstructural changes during cryorolling of Al–Mg–Si alloy

(2015) N. Naga Krishna et al.   MATERIALS CHARACTERIZATION

Enhancing mechanical properties of Al–Mg–Si–Cu sheets by solution treatment substituting for recrystallization annealing before the final cold-rolling

(2015) Hai Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of cross-rolling on the mechanical properties of an accumulative roll bonded aluminum alloy AA6014

(2014) Mathis Ruppert et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy

(2013) Kaka Ma et al.   ACTA MATERIALIA

Crystal plasticity modeling of the effect of precipitate states on the work hardening and plastic anisotropy in an Al–Mg–Si alloy

(2013) N. Anjabin et al.   COMPUTATIONAL MATERIALS SCIENCE

The coexistence of two S (Al2CuMg) phases in Al–Cu–Mg alloys

(2012) M.J. Styles et al.   ACTA MATERIALIA

Texture-Induced Anisotropy in Asymmetrically Rolled Aluminium Alloys

(2011) Jurij J. Sidor et al.   ADVANCED ENGINEERING MATERIALS

Introduction to texture analysis: macrotexture, microtexture and orientation mapping. By Olaf Engler and Valerie Randle. Pp. 456. 2nd ed. Boca Raton: CRC Press, 2010. Price (paperback) USD 129.95. ISBN 978-1-4200-6365-3.

(2010) Werner Skrotzki   JOURNAL OF APPLIED CRYSTALLOGRAPHY

Microstructural and crystallographic aspects of conventional and asymmetric rolling processes

(2008) Jurij Sidor et al.   ACTA MATERIALIA