Multiscale in-situ studies of strain-induced martensite formation in inter-critically annealed extra-low-carbon martensitic stainless steel

Evolution of substructure in low-interstitial martensitic stainless steel during tempering

(2020) F. Niessen et al.   MATERIALS CHARACTERIZATION

Lath martensite plasticity enabled by apparent sliding of substructure boundaries

(2019) C. Du et al.   MATERIALS & DESIGN

On the mechanical heterogeneity in dual phase steel grades: Activation of slip systems and deformation of martensite in DP800

(2019) Chunhua Tian et al.   ACTA MATERIALIA

Stress partitioning among ferrite, martensite and retained austenite of a TRIP-assisted multiphase steel: An in-situ high-energy X-ray diffraction study

(2018) Chenghao Song et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Compositional analysis on the reverted austenite and tempered martensite in a Ti-stabilized supermartensitic stainless steel: Segregation, partitioning and carbide precipitation

(2018) J.D. Escobar et al.   MATERIALS & DESIGN

Effect of reverted austenite on tensile and impact strength in a martensitic stainless steel−An in-situ X-ray diffraction study

(2017) Manfred Wiessner et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

In Situ Investigation of the Evolution of Lattice Strain and Stresses in Austenite and Martensite During Quenching and Tempering of Steel

(2017) M. Villa et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Kinetics analysis of two-stage austenitization in supermartensitic stainless steel

(2017) Frank Niessen et al.   MATERIALS & DESIGN

Multiple mechanisms of lath martensite plasticity

(2016) L. Morsdorf et al.   ACTA MATERIALIA

Effect of martensitic phase transformation on the behavior of 304 austenitic stainless steel under tension

(2016) H. Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Plasticity of lath martensite by sliding of substructure boundaries

(2016) C. Du et al.   SCRIPTA MATERIALIA

Effect of retained austenite on subsequent thermal processing and resultant mechanical properties of selective laser melted 17–4 PH stainless steel

(2015) Tyler LeBrun et al.   MATERIALS & DESIGN

Smaller is less stable: Size effects on twinning vs. transformation of reverted austenite in TRIP-maraging steels

(2014) M-M. Wang et al.   ACTA MATERIALIA

Investigation of the mechanical stability of reversed austenite in 13%Cr–4%Ni martensitic stainless steel during the uniaxial tensile test

(2013) Pei Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of retained austenite on austenite memory of a 13% Cr–5% Ni martensitic steel

(2012) L. Liu et al.   JOURNAL OF ALLOYS AND COMPOUNDS

High-energy synchrotron diffraction study of a transformation induced plasticity steel during tensile deformation

(2011) A Kromm et al.   JOURNAL OF STRAIN ANALYSIS FOR ENGINEERING DESIGN

In-situ synchrotron diffraction and digital image correlation technique for characterizations of retained austenite stability in low-alloyed transformation induced plasticity steel

(2010) S. Brauser et al.   SCRIPTA MATERIALIA

Load Partitioning and Strain-Induced Martensite Formation during Tensile Loading of a Metastable Austenitic Stainless Steel

(2009) P. Hedström et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

In situ neutron diffraction investigation of the collaborative deformation–transformation mechanism in TRIP-assisted steels at room and elevated temperatures

(2008) O. Muránsky et al.   ACTA MATERIALIA

SEM/EBSD basedin situstudies of deformation induced phase transformations in supermartensitic stainless steels

(2008) M. Karlsen et al.   MATERIALS SCIENCE AND TECHNOLOGY