A study of T11 boiler steel protection by cold sprayed Inconel 738 coating against high temperature erosion

Tribological behaviour of atmospheric plasma and high velocity oxy-fuel sprayed WC-Cr3C2-Ni coatings at elevated temperatures

(2020) Digvijay G. Bhosale et al.   CERAMICS INTERNATIONAL

Correlation of Microstructure and Properties of Cold Gas Sprayed INCONEL 718 Coatings

(2020) R. Vaßen et al.   JOURNAL OF THERMAL SPRAY TECHNOLOGY

Comparative micromechanical analysis of alloy 625 coatings deposited by air plasma spraying, wire arc spraying, and cold spraying technologies

(2020) Fardad Azarmi et al.   MECHANICS OF MATERIALS

Sliding and erosion wear behaviour of thermal sprayed WC-Cr3C2-Ni coatings

(2020) Digvijay G. Bhosale et al.   SURFACE & COATINGS TECHNOLOGY

Synergistic effect of the addition of TiO2 feedstock on solid particle erosion of Ni/Al2O3 and Ni/Cr2O3 coatings

(2019) Varinder Singh et al.   WEAR

Erosion behaviour of AISI 310 stainless steel at 450 °C under turbulent swirling impinging jets

(2019) J. Zaragoza-Granados et al.   WEAR

Microstructural and mechanical properties of high-performance Inconel 718 alloy by cold spraying

(2019) Wenhua Ma et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Failure assessment of ASTM A213-T12 superheater boiler tubes in a natural gas liquid plant

(2018) Arezoo Firouzeh et al.   ENGINEERING FAILURE ANALYSIS

Density determination and simulation of Inconel 718 alloy at normal and metastable liquid states

(2018) H.P. Wang et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Deposition characteristics of cold sprayed Inconel 718 particles on Inconel 718 substrates with different surface conditions

(2018) Wen Sun et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of coating thickness on residual stress and adhesion-strength of cold-sprayed Inconel 718 coatings

(2018) R. Singh et al.   SURFACE & COATINGS TECHNOLOGY

Combating hot corrosion of boiler tubes – A study

(2018) Santosh Kumar et al.   ENGINEERING FAILURE ANALYSIS

Deposition of FeCoNiCrMn high entropy alloy (HEA) coating via cold spraying

(2018) Shuo Yin et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Wear and Corrosion Resistance of Thick Ti-6Al-4V Coating Deposited on Ti-6Al-4V Substrate via High-Pressure Cold Spray

(2017) N. W. Khun et al.   JOURNAL OF THERMAL SPRAY TECHNOLOGY

Experimental study on the erosion behavior of WC-based high-velocity oxygen-fuel spray coating

(2017) Chao Zheng et al.   POWDER TECHNOLOGY

A novel spiral trajectory for damage component recovery with cold spray

(2017) Chaoyue Chen et al.   SURFACE & COATINGS TECHNOLOGY

Effects of substrate roughness and spray-angle on deposition behavior of cold-sprayed Inconel 718

(2017) R. Singh et al.   SURFACE & COATINGS TECHNOLOGY

High temperature erosion behavior of plasma sprayed NiCrAlY/WC-Co/cenosphere coating

(2017) Mahantayya Mathapati et al.   SURFACE & COATINGS TECHNOLOGY

Tribological behaviour of HVOF sprayed WC-12Co, WC-10Co-4Cr and Cr3C2−25NiCr coatings

(2017) Nitesh Vashishtha et al.   TRIBOLOGY INTERNATIONAL

Erosive wear behavior of Cold-Sprayed Ni-WC composite coating

(2017) Sima Ahmad Alidokht et al.   WEAR

Optimization and erosion wear response of NiCrSiB/WC–Co HVOF coating using Taguchi method

(2016) Ayyappan Susila Praveen et al.   CERAMICS INTERNATIONAL

Precipitation behavior during high-temperature isothermal compressive deformation of Inconel 718 alloy

(2016) Hongjun Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Study of mechanical properties and high temperature oxidation behavior of a novel cold-spray Ni-20Cr coating on boiler steels

(2015) Narinder Kaur et al.   APPLIED SURFACE SCIENCE

An investigation into microstructure and mechanical properties of cold sprayed 7075 Al deposition

(2015) M.R. Rokni et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Behavior of Ni-Based Superalloys in an Actual Waste Incinerator Plant Under Cyclic Conditions for 1,000 h at 900°C

(2014) Harminder Singh et al.   CORROSION

Analysis of material degradation for uncoated and NiCoCrAlY cold spray coated Superfer 800H in the secondary chamber of medical waste incinerator

(2014) Sukhminderbir Singh Kalsi et al.   ENGINEERING FAILURE ANALYSIS

Experimental investigation on erosion resistance of iron boride coatings for steam turbines at high temperatures

(2014) Liu-xi Cai et al.   PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY

Performance of cold spray coating in industrial medical waste incinerator

(2014) S. B. S. Kalsi et al.   SURFACE ENGINEERING

Cold Spray Forming of Inconel 718

(2012) W. Wong et al.   JOURNAL OF THERMAL SPRAY TECHNOLOGY

The influence of erodent hardness on the erosion behavior of detonation sprayed WC-12Co coatings

(2011) P. Suresh Babu et al.   WEAR

Residual stress and thermo-mechanical properties of cold spray metal coatings

(2010) V. Luzin et al.   ACTA MATERIALIA

Influence of Helium and Nitrogen Gases on the Properties of Cold Gas Dynamic Sprayed Pure Titanium Coatings

(2010) Wilson Wong et al.   JOURNAL OF THERMAL SPRAY TECHNOLOGY

Effects of Coating Thickness, Test Temperature, and Coating Hardness on the Erosion Resistance of Steam Turbine Blades

(2009) Shun-sen Wang et al.   JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME

Evaluation of cyclic hot corrosion behaviour of detonation gun sprayed Cr3C2–25%NiCr coatings on nickel- and iron-based superalloys

(2008) Subhash Kamal et al.   SURFACE & COATINGS TECHNOLOGY

Characterisation and erosion behaviour of NiCrAlY coating produced by plasma spray method on two different Ni-based superalloys

(2007) S.B. Mishra et al.   MATERIALS LETTERS